Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
The appliance should only be connected to a mains power supply equipped with an adequate earth connection and a d erential security breaker (30 mA) to cut the electricity supply in the instance of a short circuit. 5.3.1 Use of extension cables Use cables featuring “IPX5” protection level. The cross-section of the extension cable should be proportionate to its length; the longer it is, the greater its cross-section should be. See table I. 5.4 Water supply connection Caution -Danger! Only clean or tered water should be used for intake. The delivery of the water intake tap should be equal to that of pump capacity. Place the appliance as close to the water supply system as possible. 5.4.1 Connection points • Water outlet (OUTLET) • Water inlet with ter (INLET) 5.4.2 Connection to the mains water supply The appliance can be connected directly to the mains drinking wat ted with a ow preventer valve as per current regulations in force. Make sure that the hose is at least O 13 mm and that it is reinforced. 6 ADJUSTMENT INFORMATION FIG.3 6.1 Adjusting the spray nozzle (for models with this feature) Water ow is adjusted by regulating the nozzle (E). 6.2 Adjusting the detergent (on models with this feature) Detergent ow is adjusted using the regulator (F). 6.3 Adjusting the detergent pressure Set the adjustable nozzle on " " to deliver detergent at the correct pressure (on models with this feature). 6.4 Adjusting the pressure (on models with this feature) The regulator (G) is used to adjust the working pressure. The pressure is shown on the pressure gauge (where tted). 7 INFORMATION ON USE OF THE APPLIANCE FIG.4 7.1 Controls -Starter device (H). Set the starter switch on (ON/1) to: a) start the motor (in models without AS device); b) set the motor ready to start (in models with AS device). If there is a pilot light on the starter device, it should light up. If the “low/high” settings are available, use them as follows: Low : low pressure washing High : high pressure washing Set the starter device switch on (OFF/0) to shut down the appliance. If there is a pilot light on the starter device, it should go out. -Water jet control lever (I). Caution -Danger! During operation the appliance must be positioned as shown in g. 4 on a sturdy, stable surface. 7.2 Start-up Caution -Danger! Before starting up the appliance check that the water supply hose is connected properly; use of the appliance without water will damage it; do not cover the ventilation grilles when the appliance is in use. 1) Turn on the water supply tap fully. 2) Release the safety catch (D). 3) Depress the gun trigger for a few seconds and start up the appli ance using the starter device (ON/1). AS models -In AS models with automatic delivery ow cut-o system: -When the gun trigger is released the dynamic pressure automati cally cuts out the motor (see g.4); -When the gun trigger is depressed the automatic drop in pressure starts the motor and the pressure is restored after a very slight delay; -If the AS is to function correctly all gun releasing and depressing operations must be performed at intervals of less than 4-5 seconds. To prevent damage to the appliance, when running do not stop the water jet for more than 10 minutes at a time. 7.3 Stopping the appliance 1) Set the starter device switch on (OFF/0). 2) Depress the gun trigger and discharge the residual pressure inside the hoses. 3) Engage the gun safety catch (D). English 19 7.4 Restarting 1) Release the safety catch (D). 2) Depress the gun trigger and discharge the residual air inside the hoses. 3) Set the starter device on (ON/1). 7.5 Storage 1) Switch the appliance o (OFF/0). 2) Remove the plug from the socket. 3) Turn o the water supply tap. 4) Discharge the residual pressure from the gun until all the water has come out of the nozzle. 5) Drain the detergent tank. 6) Engage the gun safety catch (D). 7.6 Relling and using detergent When using detergent, the adjustable nozzle must be set on " " (on models with this feature). Fill the tank with highly degradable detergent. 7.7 Recommended cleaning procedure Dissolve dirt by applying the detergent mixed with water to the surface while still dry. When dealing with vertical surfaces work from the bottom upwards. Leave the detergent to act for 1-2 minutes but do not allow the surface to dry. Starting from the bottom, use the high pressure jet at a minimum distance of 30 cm. Do not allow the rinse water to run onto unwashed surfaces. 8 MAINTENANCE FIG.5 Any maintenance operations not covered by this chapter should be carried out by an Authorized Sales and Service Centre. Caution -Danger! Always disconnect the plug from the power socket before carrying out any work on the appliance. 8.1 Cleaning the nozzle 1) Disconnect the lance from the nozzle. 2) Remove any dirt deposits from the nozzle hole using the tool (C1). 8.2 Cleaning the lter Clean the suction lter (L) and the detergent lter after every 50 hours of operation. 8.3 Unjamming the motor (on models w...
Эта инструкция также подходит к моделям:Моечное оборудование - PW1550 (5.38 mb)