Оценок - 2, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
When your TV does not have an S VIDEO input, connect the component via the VIDEO INPUT connector using the video connecting cord (not supplied) instead of the S video cord. For details, see page 8. Refer to the instructions supplied with your TV. • Refer to the instructions supplied with the component to be connected. • You cannot make digital audio recordings of discs recorded in multi-channel surround format directly using an MD deck or DAT deck. • When you connect the component via the DIGITAL OUT OPTICAL or COAXIAL connector, set Virtual Enhanced Surround (VES) to “OFF.” Otherwise, the player will not output the following signals from the DIGITAL OUT OPTICAL or COAXIAL connector. – Dolby Digital signals (when you set “DOLBY DIGITAL” in “AUDIO SETUP” to “D-PCM”) – MPEG AUDIO When you have made the connections using an optical or coaxial digital connecting cord, do not set “DOLBY DIGITAL” to “DOLBY DIGITAL,” “MPEG” to “MPEG” and “DTS” to “ON.” If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the speakers to be damaged. Setups for the player Some setup adjustments are necessary for the player depending on the components to be connected. Use the setup display to change the various settings. For details on using the setup display, see page 45. • To listen to the sound through speakers connected to a receiver (amplifier) which has a digital connector and lacks a built-in DTS, Dolby Digital or MPEG decoder, or to output the sound to a digital component such as a DAT or MD deck Set the “AUDIO SETUP” items in the setup display (page 55) as shown in the illustration below. These are the default settings. AUDIO SETUP AUDIO ATT: AUDIO DRC: DOWNMIX: DIGITAL OUT: To set, press , then . To quit, press . OFF STANDARD DOLBY SURROUND ON ENTER DOLBY DIGITAL: MPEG: D-PCM PCM DTS: OFF DISPLAY Set the items as shown Set “VES” to “OFF” in the Control Menu display (page 35). When you select any VES mode other than “OFF,” no sound will come from the speakers. Note When you output the signals which do not reproduce the Dolby Surround (Pro Logic) effect from the DIGITAL OUT OPTICAL or COAXIAL connector, set “DOWNMIX” to “NORMAL” in “AUDIO SETUP” in the setup display (page 55). Getting 11 2+1 Channel Surround Hookups Getting Started This connection is for listening to the sound through the left and right speakers of the TV, or speakers connected to a receiver and the subwoofer. You can enjoy rich bass frequencies by connecting a subwoofer. Refer to the instructions supplied with the component to be connected. Set “SUBWOOFER” in “SPEAKER SETUP” to “YES” in the setup display (page 57). Then set “FRONT SPEAKER SIZE” to “TV” when you use the TV’s speakers, or to “LARGE,” “MIDDLE” or “SMALL” when you use the speakers connected to the receiver. zYou can enjoy surround sounds even if you connect front speakers only You can use 3D sound imaging to create virtual rear speakers from the sound of the front speakers (L, R) without using actual rear speakers (Virtual Enhanced Surround). For details, see page 35. CD/DVD player Required cords Audio connecting cord (not supplied) (1) White (L) Red (R) White (L) Red (R) S video cord (not supplied) (1) When connecting the cords, be sure to match the color-coded cord to the appropriate jacks on the components: Red (right) to Red and White (left) to White. Be sure to make connections firmly to avoid hum and noise. Monaural audio cord (not supplied) (1) One for a subwoofer COMPONENT VIDEO OUT Y1 2 1 2 CB/B-Y CR/R-Y VIDEO OUT S VIDEO OUTDIGITAL OUT COAXIAL OPTICAL AUDIO OUT WOOFER 1 R L PCM/DTS/MPEG/ DOLBY DIGITAL 2 CD INPUT L R L S VIDEO AUDIO VIDEO R INPUT To AUDIO OUT TV Receiver (Amplifier) To audio input To S VIDEO OUT To S VIDEO input To AUDIO OUT (WOOFER) To audio input or To an AC outlet Subwoofer (Active type) : Signal flow Notes You cannot enjoy a picture with an S video signal if your TV does not conform to the S video signal. When your TV does not have an S VIDEO input, connect the component via the VIDEO INPUT connector using the video connecting cord (not supplied) instead of the S video cord. For details, see page 8. Refer to the instructions supplied with your TV. 12 5.1 Channel Surround Hookups With DVDs which contain DTS, Dolby Digital or MPEG AUDIO sound, you can enjoy the surround sound while producing the effect of being in a movie theater or a concert hall using a digital component with a built-in DTS, Dolby Digital or MPEG decoder (not supplied). The player outputs the surround sound signals from the DIGITAL OUT OPTICAL and COAXIAL connectors. Using a receiver (amplifier) having the OPTICAL or COAXIAL connector and 6 speakers, you can enjoy even greater real audio presence in the comfort of your own home. Note When a DVD has a sound track with 7.1 channels recorded in MPEG AUDIO format, the output audio signals are mixed down to 5.1 channels. Required cords Optical digital connecting cord* (not supplied) (1) Coaxial digital connecti...
Эта инструкция также подходит к моделям:DVD-проигрыватели - DVP-S336 (1.03 mb)
DVD-проигрыватели - DVP-S345 (1.03 mb)