Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Now when you rewind the tape, it will automatically stop at the spot where you cleared the counter. (Notice it moves just past the marker and then back to it.) Press PLAY to watch the tape from that preselected spot. • Press DISPLAY to take the counter display off. The spot is still in memory until you set a new one or until the tape is ejected. Jump Forward or Backward with INDEX Using the time counter, you can search for a spot a certain number of minutes before or after your current position on the tape. Press STOP, if tape is playing, and press INDEX to bring up the Set Go-To Time Screen: SET GO-TO TIME TIME -:-- INDEX PRESS F.FWD OR REWIND TO START SCAN AND PLAY *TO END PRESS INDEX Basic Operations (Recording) Select minutes by pressing buttons 0 to 9 - one digit for hours, then two digits for minutes. Then press F.FWD if you want to move that many minutes ahead, or REW if you want to move that many minutes backward. For example, say you want to review a scene that began about 2 minutes earlier in a video, press 0, 0, and 2 to display 0:02 on the screen. Then press REW. The tape rewinds to the place 2 minutes back from where you began, then starts playback automatically from that spot. Jump to an Index Mark with INDEX A quick way to access specific program segments is with the index search feature. This lets you move through a tape that has several recordings on it by searching for the INDEX "mark". This function only works with recordings that have been set up with indexing. You create an INDEX mark every time you press the REC and PLAY buttons at the same time on the remote control or the REC/IRT button on the VCR. For more on how this gets recorded, see the section on Recording a Program (page 30). This VCR's indexing system is based on the VHS Standard Indexing System (VISS). The new system may not recognize index marks on tapes recorded on older VCRs. • If the VCR is in PLAY mode, press STOP. • Press INDEX on the remote control. This brings up Set Go-To Time/Index screen. • Press REW or F.FWD to begin the index search. The tape rewinds or fast-forwards until an index mark is detected. When the VCR finds an index mark, it plays 15 seconds of the program that begins at that spot. During this period, the words SCAN AND PLAY will be displayed on the bottom of your screen. • If this is the program you were looking for, press INDEX and the VCR will stop searching. Or press PLAY, resume normal playback. • If this is not the program you want, don't press anything. After 15 seconds, the VCR will move to the next mark and play a part of that program. The VCR will continue searching until you press INDEX again or PLAY reach the end of the tape. When you find the program you want, press INDEX and the VCR returns to PLAY mode. To stop the index search before an index mark is reached, press STOP. If there are no index marks on the tape, the VCR will just rewind to beginning or fast forward to the end. Basic Operations (Recording) • Recording a Program Before you Record Basic Operations (Recording) • The VCR must be hooked up properly for recording. See the Simple Hookups at the beginning of this manual. • Make sure you are familiar with the Easy Guide System for on-screen programming (page 18) and the basics about videocassettes and VCR safety. Copyright Infringement Warning Most television programs and films are copyrighted. This means that someone has legal rights governing the reproduction and distribution of this material. In certain circumstances, copyright law may apply to private in-home taping of copyrighted materials. In most cases, it is okay to record for personal use, as long as you do not sell the material. You must act responsibly in this area - check into the matter if you are unsure. Basic Recording Steps 1. Load the videocassette into the VCR with the label side up and the arrow pointing toward the VCR. The power comes on automatically when the tape is fully inserted. 2. Turn the TV to channel 3 or 4 (the one you set the switch to on the back of your VCR). Or, if you are hooked up with a direct audio/video cable, set the TV to AUX or VIDEO. 3. Press TAPE SPEED on the remote control to select SP (standard play, for the best picture quality) or EP (extended play, for longest recording time on a single tape). An indicator on the VCR's display shows which speed is active. 4. Set the VCR to the channel you want to record from. Use the up and down CHANNEL buttons to flip through the channels, or use the number buttons to go directly to the channel you want. 5. To begin recording, press REC and PLAY on the remote control at the same time or REC/IRT on the VCR. Start recording at least 10 seconds before the program starts, to make sure you catch the beginning frames. Recording will start unless the cassette is protected with the safety tab. If this tab has been removed, the VCR will eject the tape to prevent recording over what is there. (See About Videocassette Tapes for more about preventing tape e...
Эта инструкция также подходит к моделям:DVD-проигрыватели - VT-M171A (777.37 kb)