Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Rear of DVD+VCR Antenna Antenna OR OR Rear of DVD+VCR R AUDIO INPUTVIDEO INPUT ANTENNA INPUT Rear of TV A1VR YPbPr COMPONENT/PROGRESSIVE SCAN VIDEO INPUT LR AUDIO INPUT Rear of TV A2C 11 Preparation Connecting anConnecting an AntennaAntenna or Cable TVor Cable TV aAntenna: Disconnect the antenna from the rear of the TV and identify the antenna cable. If it is a round 75 ohm coaxial cable connect it directly to the jack marked ANT.IN on your DVD+VCR. If your anten- na cable is flat connect it to a 300-ohm to 75-ohm antenna adaptor (not supplied) and slip the adap- tor over the ANT.IN jack. Don’t attempt to screw it into to the DVD+VCR. bCable TV: If your cable connection has no converter or descrambler, unscrew the cable from your TV and attach it to the ANT.IN jack on the DVD+VCR. If a converter is required connect a coaxial cable from the wall jack to the IN connector on the converter, and a coaxial cable from the OUT connector on the converter to the ANT IN on your DVD+VCR. This cable hookup permits both TV and DVD+VCR operation. To view or record a CATV channel when using cable box 1. Tune the TV to the DVD+VCR output channel (CH 3 or 4). 2. Set the DVD+VCR channel selector to the cable output channel. (Example: CH3) 3. Select a channel using the cable converter. Notes: • With this connection, you cannot record one pro- gram while viewing another. • If you are using a cable box to tune channels, it is not necessary to do Auto Channel Set. Basic TV ConnectionsBasic TV Connections Make one of the following connections, depending on the capabilities of your TV. Rear of DVD+VCR Antenna Antenna OR OR Rear of DVD+VCR R AUDIO INPUTVIDEO INPUT ANTENNA INPUT Rear of TV A1VR YPbPr COMPONENT/PROGRESSIVE SCAN VIDEO INPUT LR AUDIO INPUT Rear of TV A2C RF coaxial connection Connect the RF.OUT jack on the DVD+VCR to the antenna in jack on the TV using the supplied 75-ohm Coaxial Cable (R). How to set the DVD+VCR’s RF output channel 1. When the DVD+VCR is turned off, press and hold both CH - and CH + on the front panel for more than five seconds. “RF03” or “RF04” appears in the display window. 2. Press either CH - or CH + to change the RF output channel (RF03 or RF04). Tune the TV to this channel. 3. Turn off the DVD+VCR. Audio/Video connection 1. Connect the DVD/VCR VIDEO OUT jack on the DVD+VCR to the video in jack on the TV using an optional video cable (V). 2. Connect the Left and Right DVD/VCR AUDIO OUT jacks on the DVD+VCR to the audio left/right in jacks on the TV (A1) using an optional audio cables. Note: If you use this connection, set the TV’s source selector to VIDEO. Optional TV Connections Optional TV ConnectionsOptional TV Connections These connections support only DVD playback. The tuner and VCR still output through the RF.OUT (R) or DVD/VCR OUT (A, V) jacks. Component Video / Progressive Scan connection If your television is a high-definition or “digital ready” television, you may take advantage of the DVD+VCR’s progressive scan output for the highest video resolution possible. 1. Connect the COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks on the DVD+VCR to the corresponding in jacks on the TV using an optional Y Pb Pr cable (C). 2. Connect the Left and Right AUDIO OUT jacks of the DVD+VCR to the audio left/right in jacks on the TV (A2) using an optional audio cables. Notes: • When you use Composite Video signal, set the Progressive Scan to “Off” on the setup menu. • Progressive scan does not work with the Composite video connections (yellow VIDEO OUT jack). • If your TV does not accept the Progressive Scan format, the picture will appear scrambled. Switch to composite video output. Audio Connection for DVD Audio Connection for DVDAudio Connection for DVD You can listen to playback using DVD/VCR AUDIO OUT (A1), AUDIO OUT (A2), COAXIAL (X) and RF. OUT (R) connections. COAXIAL (X) and AUDIO OUT (A2) is used only for listening to DVD playback. (See page 11.) Connecting to an amplifier equipped with two channel analog stereo Connect the Left and Right AUDIO OUT (or DVD/VCR AUDIO OUT) jacks on the DVD+VCR to the audio left and right in jacks on your amplifier, receiver, or stereo system using an optional audio cables (A1, A2). 12 13 Preparation Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/Video receiver equipped with a multi- channel decoder (Dolby Digital™, MPEG 2, or DTS) 1. Connect the DVD+VCR’s DIGITAL AUDIO OUT jacks (COAXIAL X) to the corresponding in jack on your amplifier. Use a digital (COAXI- AL X) audio cable. 2. You will need to activate the DVD+VCR’s digi- tal output. (See “AUDIO” on page 18). Digital Multi-channel sound A digital multi-channel connection provides the best sound quality. For this you need a multi-channel Audio/Video receiver that supports one or more of the audio formats supported by your DVD+VCR (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver. Caution: This DVD+VCR is not equipped with D...
Эта инструкция также подходит к моделям:DVD-проигрыватели - HR-XVC18BUS (1.82 mb)