Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Note: Rotate chuck sleeve in the direction of the arrow marked UNLOCK to loosen the chuck jaws. • Do not use a wrench to tighten or loosen the chuck jaws. • Remove drill bit from chuck jaws. USING DEPTH GAGE ROD See Figure 9. A depth gage rod has been packed with your hammer drill to assist you in controlling the depth of drilled holes. • Loosen wing screw on auxiliary handle. • Orient depth gage rod so that markings on depth gage rod face markings on wear plate. See Figure 4. Insert depth gage rod through hole on auxiliary handle. • Adjust depth gage rod so that the drill bit extends beyond the end of the. rod to the required drilling depth. • Tighten wing screw securely. This secures depth gage rod at desired depth of cut. It also secures auxiliary handle. WING SCREW WEAR PLATE DRILLBIT TO DEPTH DRILLING AUXILIARY DEPTH HANDLE DRILLING DEPTH MARKINGSON DEPTHGAGEROD Fig. 9 When drilling holes with the depth gage rod installed, the desired hole depth has been reached when the end of the rod comes in contact with the surface of the material being drilled. Fig. 8 10 _, WARNING:Alwayswearsafetygogglesorsafety glasseswithsideshieldswhenoperatingtools. Failureto dosocouldresultin objectsbeingthrown intoyoureyes,resultingin possibleseriousinjury. CHARGINGBATTERYPACK Thebatterypackforthistoolhasbeenshippedin alow chargeconditionto preventpossibleproblems.Therefore, youshouldchargeit untillightonfrontof chargerchanges fromredtogreen. Note:Batterieswillnotreachfullchargethefirsttimethey arecharged.Allowseveralcycles(drillingfollowedby recharging)forthemtobecomefullycharged. TO CHARGE • Charge battery pack only with the charger provided. • Make sure power supply is normal house voltage, 120 volts, 60 Hz, AC only. • Connect charger to power supply. • Attach battery pack to charger by aligning raised ribs on battery pack with grooves in charger, then slide battery back onto charger. See Figure 10. BATTERY PACK TO REMOVE CHARGER TO ATTACH GROOVES Fig, 10 • Red light should turn on. Red light indicates fast charging mode. If red light is flashing, this indicates battery pack is deeply discharged or hot. If battery pack is hot, red light should become steady after battery pack has cooled down. If battery pack is deeply discharged, red light should become steady after voltage has increased, normally within 60 minutes. If after one hour red light is still flashing, this indicates a defective battery pack and should be replaced. Green light on indicates battery pack is fully charged and slow charging to maintain battery pack. Yellow light on and red light flashing indicates defective battery pack. Return battery pack to your nearest Sears Repair Center for checking or replacing. • When your battery pack becomes fully charged, the red light will tum OFF and the green light will tum ON, • After normal usage, 1 hour of charging time is required to be fully charged. A minimum charge time of 1-1/2 hours is required to recharge a completely discharged tool. • The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. • Do not place charger in an area of extreme heat or cold. It will work best at normal room temperature. • When the batteries become fully charged, unplug your charger from power supply and remove the battery pack. LED FUNCTION OF CHARGER LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK: • Red LED Lighted = Fast Charging Mode. • Green LED Lighted = Fully Charged And Slow Charging To Maintain Battery Pack. • Red LED Flashing = Hot Or Deeply Discharged Battery Pack. Also Defective Battery Pack After 1 Hour. • Yellow LED Lighted and Red LED Flashing = Defective Battery Pack. IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES Under extreme continuous use, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 1 hour before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the red light on your battery charger to flash. When battery pack cools down, red light will glow continuously indicating fast charging mode, 1 hour charge time. Once the battery pack cools down, it will recharge battery pack in fast charging mode as normal. Note: This situation only occurs when extreme continuous use of your drill causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears repair center for electrical check. 11 SWITCH See Figure 11. To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. FORWAR_REVERSE SELECTOR CENTERPOSITION (LOCK) TRIGGER Fig, 11 VARIABLE SPEED This tool has a variable speed switch that delivers higher speed and torque with increased trigger pressure, Speed is controlled by t...