Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
A forward/reverse control button (3) determines the direction of the tool and also serves as a lock off button. • To select forward rotation, release the trigger switch and push the forward/reverse button forward as shown in figure D. • To select reverse, release the trigger switch and pull the forward/reverse button backward as shown in figure D. • The neutral (no run) position of the button locks the tool in the off position. When changing the position of the button, be sure the trigger is released. DRILLING • Use sharp drill bits only. • Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and should be pulled out frequently when drilling to clear chips from the flutes. • Support and secure work properly, as instructed in the safety Instructions. • Use appropriate and required safety equipment, as instructed in the safety instructions. • Secure and maintain work area, as instructed in the safety instructions. • Use light pressure until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit • Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole. • Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. • Make sure switch turns tool on and off. WARNING: It is important to support work properly and to hold the tool firmly to prevent loss of control which could cause personal injury. HINTS FOR OPTIMUM USE • Always use the correct type of screwdriver bit. Never use a screwdriver bit tip without a bit tip holder • If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant. • Always hold the tool and screwdriver bit in a straight line with the screw. MAINTENANCE Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts. TROUBLESHOOTING Problem Possible Cause Possible Solution • Tool will not start. • Battery not charged. • Check battery charging requirements. • Battery will not charge. • Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details. • Check current at receptacle by plugging in a lamp or other appliance. • Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. • Surrounding air temperature • Move charger and tool too hot or too cold. to a surrounding air temperature of above 40 degrees F (4,5°C) or below 105 degrees F (+40,5°C). For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. Accessories Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-544-6986. WARNING: The use of any accessory not recommended for use with this tool could be hazardous. BATTERY REMOVAL Before attempting to disassemble this tool, turn it on and run it in either direction until it stops to ensure a complete discharge of the batteries. Using a phillips screwdriver, remove the screws in the product housing and lift the housing half from the tool. Disconnect the terminal clips from the batteries and lift the batteries out. See “Service Information” for battery replacement. The RBRC™ Seal The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel- cadmium battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative. RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickel- cadmium batteries. Help protect our environment and conserve natural resources by returning the spent nickel-cadmium battery to an authorized Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or call 1-800-8-BATTERY. SERVICE INFORMATION All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical a...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - CSD300T (273.97 kb)