Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Any cord marked for outdoor use can also be used for indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable for outdoor use. b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size. 9. Use only the supplied charger when charging your tool. The use of any other charger could damage the tool or create a hazardous condition. 10. Use only one charger when charging. 11. Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center. 12. DO NOT incinerate the battery pack even if they are severely damaged or completely worn out. The battery can explode in a fire. 13. A small leakage of liquid from the battery pack cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide. CHARGING PROCEDURE IMPORTANT: The batteries in your tool are not fully charged at the factory. Before attempting to charge them, thoroughly read all of the safety instructions. To charge the tool, follow the steps below: 1. Insert the jack plug (5) of the charger (4) into the charging port (6) in the bottom of the tool handle as shown in figure B. 2. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. 3. Let the tool charge initially for 17 hours. WARNING: When disconnecting the tool from the charger, be sure to unplug the charger (6) from the outlet first, then disconnect the jack plug (5) from the tool. IMPORTANT CHARGING NOTES 1. Charger will work best at normal room temperature. 2. The charger plug and the tool handle may become warm while charging. This is normal and does not indicate a problem. 3. A minimum charge time of 17 hours is required to recharge a completely discharged tool. 4. For most fix up jobs a shorter charge time may be adequate. SAFETY WARNINGS AND INSTRUCTIONS: DRILLING • Hold tool firmly to control its twisting action. WARNING: Tool may stall (if overloaded or improperly used) causing a twist. To reduce the risk of injury always expect the stall. Grip the tool firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting. OPERATING INSTRUCTIONS REMOVING AND INSTALLING BITS • Insert power hex bit or bit tip with bit tip holder into the cavity in the spindle (1) until it snaps into place. • To remove the bit pull it straight out. If bit does not fit into spindle, rotate the bit and re-insert it. Do not insert a bit tip without a bit tip holder. TRIGGER SWITCH & FORWARD/REVERSE SLIDER The tool is turned ON and OFF by pulling and releasing the trigger switch (2). A forward/reverse control button (3) determines the direction of the tool and also serves as a lock off button. • To select forward rotation, release the trigger switch and push the forward/reverse button forward as shown in figure D. • To select reverse, release the trigger switch and pull the forward/reverse button backward as shown in figure D. • The neutral (no run) position of the button locks the tool in the off position. When changing the position of the button, be sure the trigger is released. DRILLING • Use sharp drill bits only. • Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and should be pulled out frequently when drilling to clear chips from the flutes. • Support and secure work properly, as instructed in the safety Instructions. • Use appropriate and required safety equipment, as instructed in the safety instructions. • Secure and maintain work area, as instructed in the safety instructions. • Use light pressure until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit • Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole. • Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. • Make sure switch turns tool on and off. WARNING: It is important to support work properly and to hold the tool firmly to prevent loss of control ...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 90530144 (273.97 kb)