Оценок - , средний балл: ( )

Инструкция по эксплуатации Milwaukee, модель 0234-6

Производитель: Milwaukee
Размер: 266.12 kb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Use the open end wrench is turned on. 1/16" off of the bottom. provided to hold the Right Angle Drive When using screwdriver bits, insert the WARNING! To reduce the risk of injury, al-ways wear eye protection. spindle before attempting to loosen the bit far enough for the chuck jaws to chuck. grip the hex of the bit. 2. To close the chuck jaws, hold the collar while turning the sleeve in the clockwise direction. Tighten securely. Chuck Removal (Fig. 7) Installing Bits into Keyless Chucks This tool is equipped with a threaded spindle (Fig. 5 & 6) Cat. No. 0235-21 to hold the chuck. Before removing the 1. Remove the chuck from the drill follow- These tools are equipped with a spindle- chuck, unplug the tool and open the chuck ing instructions (See “Removing the lock mechanism and a single-sleeve key- jaws. A left-handed thread screw is lo- Chuck From the Drill”). Slip the double less chuck. Always unplug the tool before cated inside the chuck to prevent the chuck hex coupling (1) over the hex on the inserting or removing bits. from loosening when the tool is operated drill spindle. 1. To open the chuck jaws, turn the chuck in reverse direction. Remove the screw by sleeve in counterclockwise direction. turning it clockwise. To remove the chuck, Loosen the clamping screws on the hold the tool so that only the side of the clamping sleeve (2) and slip the sleeve 2. To install a bit, open the chuck jaws chuck rests firmly and squarely on a solid onto the drill collar. slightly wider than the bit. Center the bit workbench. Insert the chuck key or a chuck 2. Slide the Right Angle Drive head (4) into in the chuck jaws and lift it about remover bar in one of the keyholes. Turn the other side of the sleeve and turn 1/16" off of the bottom. Align the bit as the chuck so the key is at about a 30° angle the drive head slightly in either direc shown (Fig. 5). to the bench top and strike the key sharply tion so the hexagonal hole in the cou with a hammer so the chuck turns in a pling (1) engages the hexagonal por counterclockwise direction (looking from tion of the spindle (3). 8 9 3. To close the chuck jaws, turn the chuck sleeve in clockwise direction (Fig. 6). Tighten securely. Several detents will be felt as the chuck sleeve is turned. Fig. 7 Attaching Right Angle Drive to Drill (Fig. 8) Collar SleeveFig. 4 Cat. No. 0233-20 To reduce the risk of injury, always wear eye protection. WARNING! Using Forward/Reverse Switch (Fig. OPERATION 1. To lock the trigger, hold the lock button in while pulling the trigger. Release the trigger. 2. To unlock the trigger, pull the trigger and release. The lock button will pop out. To reduce the risk of injury, always wear eye protection. WARNING! Using Forward/Reverse Switch (Fig. OPERATION 1. To lock the trigger, hold the lock button in while pulling the trigger. Release the trigger. 2. To unlock the trigger, pull the trigger and release. The lock button will pop out. ForwardFig. 10 Trigger Reverse To reduce the risk of explosion, electric shock and property damage, always check the work area for hidden pipes and wires before drilling. WARNING! APPLICATIONS CAPACITIES Wood Steel Masonry Cat. No. Flat Boring Bits Auger Bits Ship Auger Bits Selfeed Bits Hole Saws Twist Drill Hole Saws Carbide-Tipped Bits 0233-20 1" N R N R N R 1-3/4" 3/8" 1" 3/8" 0234-1 RAD low RAD high 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/8" 1-1/4" 1-1/2" 1" 2" 2-1/4" 1-1/2" 4" 4-1/2" 2-3/4" 1/2" 1/2" 1/2" 2" 2-1/8" 1-1/2" 1/2" 9/16" 7/16" 0234-6 RAD low RAD high 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/8" 1-1/4" 1-1/2" 1" 2" 2-1/4" 1-1/2" 4" 4-1/2" 2-3/4" 1/2" 1/2" 1/2" 2" 2-1/8" 1-1/2" 1/2" 9/16" 7/16" 0235-21 1-1/2" 1-1/2" 1-1/4" 2" 4" 1/2" 2" 1/2" 0235-6 1-1/2" 1-1/2" 1-1/4" 2" 4" 1/2" 2" 1/2" 0236-6 RAD low RAD high 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/8" 1-1/4" 1-1/2" 1" 2" 2-1/4" 1-1/2" 4" 4-1/2" 2-3/4" 1/2" 1/2" 1/2" 2" 2-1/8" 1-1/2" 1/2" 9/16" 7/16" 0244-1 RAD low RAD high 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/4" 2-1/4" 2-9/16" 1-3/4" 4-1/2" 5" 3-1/4" 1/2" 1/2" 1/2" 2-1/4" 2-1/4" 1-3/4" 9/16" 5/8" 1/2" 1. For forward (clockwise) rotation, push the forward/reverse switch to FWD as shown. 2. For reverse (counterclockwise) rotation, push the forward/reverse switch to REV as shown. Although an interlock preve...