Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
The tool speed can be controlled from the minimum to the maximum nameplate RPM by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed. This accurate speed control enables you to drill without center punching. It also permits you to use as a power screwdriver. Bits are available for driving screws as well as running bolts and nuts. FORWARD/REVERSING LEVER & TRIGGER LOCK Your tool is equipped with a forward/ reversing lever and trigger lock located above the trigger (Fig. 1). This lever was designed for changing rotation of the chuck, and for locking the trigger in an “OFF” position to help prevent accidental starts and accidental battery discharge. For forward rotation, (with chuck pointed away from you) move the lever to the far left. For reverse rotation move the lever to the far right. To activate trigger lock move lever to the center off position. !CAUTION Do not change direction of rotation until the tool comes to a complete stop. Shifting during rotation of the chuck can cause damage to the tool. GEAR SHIFTING Your tool is equipped with two separate gear ranges, low gear and high gear. Low gear provides high-torque and slower drilling speeds for heavy duty work or for driving screws. High gear provides faster speeds for drilling lighter work. To change speeds slide switch, to the high or low position. ATTENTION: If your tool appears to be running, but the chuck will not turn, check to make sure the gear shifting switch is pushed fully into desired setting. ADJUSTABLE CLUTCH Your tool features 6 clutch settings. Output torque will increase as the clutch ring, is rotated from 1 to 5. The drill “ ” position will lock up the clutch to permit drilling and driving heavyduty work, and also enables bits to be changed quickly and easily in the keyless chuck. The hammer drill position locks up the clutch for hammer drilling. The clutch ring allows the tool to be set for various drilling /hammer drilling applications. Rotate the clutch ring to the drill or hammer drill symbol depending on the below applications). Drilling mode: For drilling in woods, metals, plastics or other non concrete materials. Hammer drilling mode: For drilling in brick, block, mortar, concrete, asphalt, tile or other similar hard materials. AUXILIARY HANDLE The auxiliary handle will provide additional control, support and guidance for the tool. To mount, thread handle into hole provided in housing until tight. BRAKE When the trigger switch is released it activates the brake to stop the chuck quickly. This is especially useful in the repetitive driving and removal of screws. INSERTING BITS Move reverse switch lever to the center “OFF” position. Remove battery pack and rotate the clutch ring to the drill bit symbol “ ”. Rotate the chuck sleeve counterclockwise viewing from chuck end, and open chuck to approximate drill bit diameter. Insert a clean bit up to the drill bit flutes for small bits, or as far as it will go for large bits. CLOCKWISE COUNTER- CLOCKWISE CHUCK SLEEVEFIG. 2 Close chuck by rotating the chuck sleeve clockwise and securely tighten by hand until a noticeable "click" noise is heard, indicating that the drill bit is firmly gripped in the jaws. !WARNING Do not use the power of the drill while grasping chuck to loosen or tighten bit. Friction burn or hand injury is possible if attempting to grasp the spinning chuck. -8 REMOVING CHUCK Rotate the clutch ring to the drill bit a 3/8" hex key wrench and close jaws on flats symbol “ ”. Open the chuck all the way, of wrench. Strike long arm of wrench sharply remove left-hand thread screw inside chuck counterclockwise, remove wrench and by turning it clockwise. Insert the short arm of unthread chuck from spindle (Fig. 2). INSTALLING CHUCK Always keep the spindle threads, the threads debris. To install a chuck, reverse “removing of the chuck and securing screw free of the chuck” procedure. RELEASING AND INSERTING BATTERY PACK Release battery pack from tool by pressing battery and slide battery pack into tool until it on both sides of the battery release tabs and locks into position. Do not force. pull downwards. To insert battery, align CHARGING BATTERY PACK (1 HOUR CHARGER) Plug charger cord into your standard power mean the battery pack is too hot or too cold. outlet, then insert battery pack into The purpose of the light is to indicate that thecharger.The charger’s green indicator will battery pack is fast-charging. It does notbegin to “BLINK”. This indicates that the indicate the exact point of full charge. The battery is receiving a fast charge. Fast- light will stop blinking in less time if thecharging will automatically stop when the battery pack was not completely discharged. battery pack is fully charged. When the battery pack is fully charged, When the indicator light stops “BLINKING” unplug the charger (unless you're charging(and becomes a steady green light) fast another battery pack) and slip the batterych...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 2585 (564.23 kb)