Войти:
Оценок - 4, средний балл: 3.8 ( )

Инструкция по эксплуатации Panasonic, модель EY6181

Производитель: Panasonic
Размер: 349.39 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


(The display goes off when the overload condition is resolved.) Stop using the tool when this condition occurs. 3. Reading the battery capacity indicator during charging. (?) At the start of charging Part of the row of LED indicators lights up, according to the remaining battery capacity prior to charging. © During charging As charging progresse, additional LED indicators light up as the battery capacity increases. © Charging completed Confirm by the charging lamp(R)on the charger. (D © © Reading the battery capacity indicator by depressing the button on the battery pack. (?) Push the button. (2) The indicators light up in the following sequence-battery temperature LED ( £■) -> 24 -hour charge LED («► Pull the trigger completely more than 2 seconds. * The battery capacity indicator LED does not light up while the battery pack is being charged or being used with the main unit. ->Use up the remaining power of the battery pack, then fully charge it. 5. When the battery temperature LED lamp lights up This lamp lights up when the battery pack becomes too hot. Allow the battery pack to cool down until the lamp goes off. Note: The LED lamp will also light up in some cases when the battery pack has not been used. For example, when the ambient temperature is high (e.g. inside a car in summer), and the temperature of the battery cells inside the battery pack has become to high. 6. When the 24-hour charge LED lamp lights up After depressing the button, when this lamp lights up, charge the battery pack for about 24 hours (until the lamp goes off) to bring the batteries up to full capacity. (J) Battery charger Note: When you charge the battery pack for the first time, or after prolonged storage, charge it for about 24 hours to bring the batteries up to full capacity. EYQ2Q2 (Cat. No. EY0202B76581 1. Plug the charger into the power source. 2. Insert the battery pack firmly into the charger. 3. During charging, the charging lamp will light up. When the charge is completed, an internal electronic switch will automatically be triggered to prevent overcharging. • Charging will not occur if the battery pack is warm (for example, immediately after heavy-duty operation). The orange standby lamp (L) will light up until the battery becomes cool. Charging will then begin automatically. 4. When charging is completed, the charging lamp (R) will start flashing quickly. If a fully charged battery pack is inserted into the charger again, the charging lamp may light up and then flash quickly soon to indicate the charging is completed. 9 5. If the charging lamp does not turn on immediately after the charger has been plugged in, or if after standard charging time, the lamp does not go off, consult an authorized dealer for advice. 6. High capacity battery pack EY9103, EY9101 and EY9182 can be recharged by using EY0202. In this case, charging time is approximately 20 minutes. EY0001 (Cat. No. EY0001B) RE570 (Cat. No. EY570B7659) 1. Plug the charger into the power source. 2. Insert the battery pack firmly into the charger. 3. During charging, the charging lamp will light up. When the charge is completed, an internal electronic switch will automatically be triggered to prevent overcharging. • Charging will not occur if the battery pack is warm {for example, immediately after heavy-duty operation). • If the charging lamp does not light, check to determine whether the contacts are clean and the battery pack is inserted completely. • Give the sufficient time after use to cool down before recharging. 4. When charging is completed, the charging lamp will go out. • If a fully charged battery pack is placed in the charger again, the charging lamp may light up. 5. There is a temperature rise in the battery pack immediately after use, and if charging is started, a sufficient charge may not be obtained in the standard time. 6. If the charging lamp does not turn on immediately after the charger has been plugged in, or if after 2 hours of charging the lamp does not go off, consult an authorized dealer for advice. (R) Charging lamp (L) Standby lamp © Lock release rod Lamp indications of EY02...

Эта инструкция также подходит к моделям:
Дрели и шуропопверты - EY6101 (349.39 kb)
Дрели и шуропопверты - EY6100 (349.39 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории