Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Cluttered areas and benches invite accidents. 2) CONSIDER WORK AREA ENVIRONMENT. Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence of flammable liquids or gases. 3) GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. 4) KEEP CHILDREN AWAY. Do not let visitors contact tool. All visitors should be kept away from work area. 5) STORE IDLE TOOLS. When not in use, tools should be stored in a dry, high or locked-up place - out of reach of children. 6) DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed. 7) USE RIGHT TOOL. Don’t force small tools or attachments to do the job of a heavy duty tool. Don’t use tool for purpose not intended-for example-don’t use circular saw for cutting tree limbs or logs. 8) WEAR PROPER APPAREL. No loose clothing or jewelry to get caught in moving parts. Rubber gloves and nonskid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair. 9) USE SAFETY GLASSES with most tools. Also use face or dust mask in dusty environment. 10) SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool. 11) DON’T OVERREACH. Keep proper footing and balance at all times. 12) MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Keep handles dry, clean, and free from oil and grease. 13) DISCONNECT TOOLS/BATTERIES. When not in use, before servicing, and when changing accessories, such as bits. 14) REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15) AVOID ACCIDENTAL STARTING. Don’t carry tool with finger on switch. 16) STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired. 17) CHECK DAMAGED PARTS. Before further use of the tools, check guard or other safety devices carefully to determine that they will operate properly and perform their intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center. Have defective parts replaced by an authorized service center. Do not use a defective tool. SAVE THESE INSTRUCTIONS - 2 - FOR BATTERY CHARGER & BATTERY PACK D SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for battery chargers EY02Û2, EY0Û01 and RE570. 2) Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery pack. 3) CAUTION - To reduce the risk of injury, charge only battery pack as shown below. RE570 EY970, EY9080, EY9086 Approx. 1 hour EY0001 EY9001, EY9006 Approx. 1 hour EY0202 EY9001, EY9080, EY9065 EY9006, EY9086 Approx. 15 min. EY9101, EY9180, EY9182 EY9103 Approx. 20 min. Other types of batteries may burst causing personal injury and damage. 4) Do not expose charger to rain or snow. 5) To reduce risk of damaging the electric plug and cord, pull by plug rather than cord when disconnecting charger. 6) Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. c. that wire size is large enough for ampere rating of charger as specified below. RECOMMENDED MINIMUM AWG SIZE OF EXTENSION CORDS FOR BATTERY CHARGERS AC Input Rating. Amperes AWG Size of Cord Equal to or But less greater than than Length of Cord. Feet 25 50 100 150 0 2 18 18 18 16 8) Do not operate charger with damaged cord or plug - replace them immediately. 9) Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 10) Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 11) To reduce the risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. 12)The charger and battery pack are specifically designed to work together. Do not attempt to charge any other cordless tool or battery pack with this charger. 13) Do not attempt to charge the battery pack with any other charger. 14) Do not attempt to disassemble the battery pack housing. 15) Do not store the tool and battery pack in locations where the temperature may reach or exceed 122°F (50°C) (such as a metal tool shed, or a car in the summer), which can lead to deterioration of the storage battery. 7) An extension cord should not be used unless absolutely necessary. Use of improper extension cord cou...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - EY6181 (349.39 kb)
Дрели и шуропопверты - EY6101 (349.39 kb)