Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Do not force the battery. Insert until it locks into place. 4. The red LED light on the charging unit will come on when the battery begins its charging cycle. 5. Charge battery for 3-5 hours for a full charge from a fully depleted condition. The red LED will not go off until the battery is removed from the charger base. Battery charging with the 1 hour “Smart” charger (1 piece charger): 1. Plug the charger into an appropriate 110/120V outlet. 2. Insert the battery into the charger. The battery fits into the oval recess in only one way. Do not force the battery. Insert until it locks into place. 3. The green light over the word “OFF” on the control panel should come on. If it doesn’t, make certain the wall outlet you are plugged into is working. If the outlet power is okay, the fuse inside the charger may have blown. Fuses should be replaced by a qualified electrical technician. 4. To begin charging, press the “SET” button. A steady red light over the word “ON” should come on indicating the battery is being charged. 5. When the battery is fully charged, the red light will go off and the unit will stop charging. Remove the battery from the charger upon completion of the charge cycle. Never leave a battery unattended while charging. While charging will make the battery and charging unit warm, if it becomes hot to the touch, disconnect the charger immediately. There is a possibility of fire hazard. Have the battery and charging unit checked by a qualified electrical service technician. G8596/G8597 18V Cordless Drill -6 OPERATION Inserting Battery Into Drill 1. Insert the battery into the handle of the drill so that the long end is forward. The battery will only install in one orientation. 2. Make sure the securing clasps on either side of the drill base engage with the clips on the battery compartment. Inserting and Removing Bits and Drivers: 1. Set the direction switch, located just above the trigger, so that it is in the center position. 2. Hold the chuck by the collar while turning the sleeve (the forward section). See Figure 1. This will cause the three chuck jaws located inside the recess to open or close depending upon the direction. 3. When the jaws are at the approximate diameter of the bit or driver, insert the shank end of the bit or driver into the jaw opening. 4. Turn the sleeve clockwise until it tightens around the bit or driver. Never “power tighten” which is holding the sleeve while running the drill. This can cause a loose grip on the bit or driver and potential damage to chuck jaws. Check for tightness periodically while using the tool. 5. To release the bit or driver, hold the chuck collar, and turn the sleeve counterclockwise. Fig 1. Inserting bits into the chuck. Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glasses or goggles when operating equipment. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI). -7- G8596/G8597 18V Cordless Drill OPERATION, CONT’D Operating the drill 1. Set the Direction Switch for the desired rotation of the bit or driver. The direction switch is the sliding switch located just above the trigger. When looking down on the drill, pushing the switch all the way to the right will give a counterclockwise rotation (normally for loosening fasteners and bits), all the way to the left will be clockwise (normally for tightening fasteners and drilling holes). When the switch is in the center position it locks the switch to avoid accidentally starting the drill. 2. Set the Torque Setting Ring located just behind the chuck. This ring has 16 settings on it, and a pointer indicator embossed on the drill case. Set on 1 for very light applications such as driving screws into drywall. Use the higher settings for denser woods and materials. Use the drill bit symbol when boring holes. Using the proper torque setting will ensure that the fastener is not driven too deeply damaging the surface material, or in the worst case, stripped out of the hole due to over-torquing. 3. Select speed and pull the trigger to activate the drill. This drill has two speeds, fast and slow, controlled by a sliding switch on the top of the drill. Direction Switch ON/OFF Trigger Torque Setting Speed Selector Fig 2. Location of controls. G8596/G8597 18V Cordless Drill -8 OPERATING TIPS AND MAINTENANCE Operating Guides and Tips Avoid overloading the drill. Always use sharpened drill bits. Do not apply excessive pressure to the drill while using. If the speed drops abnormally, decrease pressure immediately. If the bit stops abruptly or becomes blocked, release the trigger at once. Reverse the direction to free the drill bit. Ensure the safety of the workplace. Clear the work area of all parts and debris that may cause injury by flying objects. Securely fix the object to be drilled or fastened in a vise or otherwise clamp to avoid injury. Do not attempt to hold workpiece...