Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Connect the HDD Activity LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD. 5. ATX power button/soft-off button (Green 2-pin PWRSW) This connector is for the system power button. Pressing the powerbutton turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings. Pressing the power switch for morethan four seconds while the system is ON turns the system OFF. 6. Reset button (Blue 2-pin RESET) This 2-pin connector is for the chassis-mounted reset button for systemreboot without turning off the system power. Chapter 2: Hardware information 16. Auxiliary panel connector (20-pin AUX_PANEL1) This connector is for additional front panel features including front panel SMB, locator LED and switch, chassis intrusion, and LAN LEDs. PIN1 DSBV-DX Series System panel auxiliary connector DSBV-DX AUX_PANEL1 I2C_4_DATA# LOCATORLED1+ +5VSBLOCATORLED1LAN1_ LINKLOCATORBTN# LAN1_ACTGND+5VSB I2C_4_CLK#GNDGND LAN2_ACTLOCATORLED2LAN2_ LINKLOCATORLED2+ CASEOPEN NC 1 2 2 5 43 4 1. Front panel SMB (6-1 pin FPSMB) These leads connect the front panel SMBus cable. 2. LAN activity LED (2-pin LAN1_LED, LAN2_LED) These leads are for Gigabit LAN activity LEDs on the front panel. 3. Chassis intrusion (4-1 pin CHASSIS) These leads are for the intrusion detection feature for chassis with intrusion sensor or microswitch. When you remove any chassiscomponent, the sensor triggers and sends a high-level signal to theseleads to record a chassis intrusion event. The default setting is short CASEOPEN and GND pin by jumper cap to disable the function. 4. Locator LED (2-pin LOCATORLED1 and 2-pin LOCATORLED2) These leads are for the locator LED1 and LED2 on the front panel. Connect the Locator LED cables to these 2-pin connector. The LEDs will light up when the Locator button is pressed. 5. Locator Button/Swich (2-pin LOCATORBTN) These leads are for the locator button on the front panel. This button queries the state of the system locator. ASUS DSBV-DX Series Chapter 2: Hardware information This chapter describes the power upsequence, and ways of shutting down thesystem. 3 Powering up Chapter summary 3 3.1 Starting up for the first time........................................................ 3-1 3.2 Turning off the computer............................................................. 3-2 ASUS DSBV-DX Series Beep Description Error Endless beep Memory module missing One continuous beep followed byshort beeps VGA controller failure Two short beeps PCI resource assignment error 3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. System power 6. After applying power, the system power LED on the system front panel case lights up. For systems withATX power supplies, the system LED lights upwhen you press the ATX power button. If your monitor complies with “green” standards or if it has a “power standby” feature, the monitor LED may light up or switch between orange and green after the system LED turns on. The system then runs the power-on self tests or POST. While the tests are running, the BIOS beeps (see BIOS beep codes table below) or additional messages appear on the screen. If you do not see anything within 30seconds from the time you turned on the power, the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance. Phoenix BIOS beep codes 7. At power on, hold down the
Домашние кинотеатры - DSBV-DX (6.72 mb)
Домашние кинотеатры - DSBV-DX/SAS (6.72 mb)