. . . . . . . . . . . . . . . . . .4, 5 A Quick Tour of Your Wine Vault . . . . . . . . . . . . . . . .6, 7 The Cellar Management System . . . . . . . . . . . . . . .8–11 Key Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Key Areas of the Cellar Management System . . . . . . . . . . .10 Tips for Stocking Your Cellar the First Time . . . . . . . . . . . . . .11 The Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . .12–17 Lockable Entry Door

3 Problem Solver ............................. 21,22 Product Registration ............................. 3 Safety Instructions ........................... /4-7 State of California Water Treatment Device Certificate ............ 26 Warranty .............................. BackCover Care and Cleaning Cleaning-Outside and Inside .................. 13 Light Bulb Replacement ....................... 1/4 Vacation ....................................... Read this manual carefully. It is intended to help y

CABINET CABINET Front edge of product case 110° Front face 120° These products will fit flush to adjacent cabinets when installed with a Dim. A-width filler panel or cleat. The filler panel should be recessed or set back behind the door and even with the front edge of the product case. NOTE: Handle and handle standoff depth is 1-3/4" Product Dim. A ZDWI240, ZDBI240 1" ZDWC240, ZDWR240 1/2" ZDBC240, ZDBR240 1/2" *For a standard installation of Custom-Framed unit: The product must be installed so

The filler strip will act as a spacer between the door case and adjacent cabinet and will prevent interference with cabinet door swing. The width of the opening must include filler panels. Note: When installed, the door should project forward 1" of adjacent 24"-deep cabinets. Side-by-Side Installation For a complete refreshment center, install a Monogram Wine Reserve and Beverage Center together. • Products must operate from separate properly grounded receptacles. Door Swing Clearances All

SAVE THESE INSTRUCTIONS IMPORTANTES INSTRUCTIONS DE SECURITE RACCORDEMENT ELECTRIQUE Ne coupez ni retirez en aucun cas la troisieme broche (mise a la terre) de la fiche du cordon d’alimentation. Pour votre securite, cet appareil doit etre correctement mis a la terre. Le cordon d’alimentation de cet appareil est muni d’une fiche a 3 broches (mise a la terre) qui se branche dans une prise mural ordinaire a 3 alveoles (mise a la terre) pour reduire au minimum les risques du chocs electriques. Faite

Pull the small slide sub-assembly completely forward. 3. Insert the sides of the drawer back into the guides. 4. Push until the tabs lock into place. Appearance may vary Sub-assembly Sub-assembly To replace, push drawer slide Pull small slide sub- arm back into unit assembly completely forward NOTE: Make sure the tabs on the full extension drawer guides are fully engaged before loading any bottles. Pull the drawers out all the way to the STOP position and push back in several times to make sure

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Reversing the Door Swing Wine Chiller To reverse the door Parts included: 1. Top left case hinge 2. Bottom left case hinge 3. Left and right side decorative hinge cover 4. Decorative hinge screw hole cover 5. Torx® driver bit Tools required: 1. Phillips screwdriver 2. Electric drill To remove the door: 1. Flatten the shipping carton to use as a pad. 2. Remove the 2 screws and the to

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Preparing Secure all loose items such as drawers by Be sure the wine reserve stays in an upright taping them securely in place to prevent position during moving. to move damage. Built-In Dimensions Wine Reserve Installation dimensions The wine reserve can be a free-standing model or can be built in using the cut-out dimensions below. (603 mm) (603 mm) 233/4. 233/4. 341/2. (876 mm) P

The cooler area will be in the middle section. The upper part of the cabinet is the warmest section. When the temperature is adjusted, allow 24 hours for the unit to stabilize. To set the control, turn it to the midpoint setting (approximately 45.F). Once the beverage center is loaded, allow at least 24 hours before making any adjustments to the initial setting. Interior light The interior light makes it easy to view your beverage labels and enhances the and switch display of your collection. Wh

Whether you chose it for its purity of design or the assiduous attention to detail, you will find that your Monogram wine chiller’s superior blend of form and function will delight you for years to come. The information on the following pages will help you operate and maintain your wine chiller properly. Contents Built-In Dimensions . . . . . . . . . . . . . . . .10 Care and Cleaning . . . . . . . . . . . . . . . .8, 9 Consumer Information . . . . . . . . . . . .2, 3 Controls and Features . . .