Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
The machine turns to keeping warm mode. collar When the hot water temperature drops below 80.C 2. Press the hot and cold dispenser buttons until / 176.F, the heating system will automatically water runs from both taps resumes. 5. Turn on the cold (green) power switch, the green 5 cooling LED indicator turns on and the cooling system starts. When the cold water reaches a 6. Allow 40 minutes for water to reach the set hot and temperature of approx. 8.C / 46.F, the green light cold temperatures. goes off and the cooling system stops working. The machine turns to keeping cool mode. When Contact a local water bottle distributor to the cold water temperature rises to 10.C / 50.F purchase water bottles. degree, the cooling system will automatically resumes. USING THE HOT WATER TAP IMPORTANT : The hot water tap has a safety feature to prevent children from accessing hot water. To dispense hot water: . Slide the safety switch on top of the hot water button up . Continue holding the safety switch up while pushing the hot water dispenser button. Hot water is dispensed as long as you keep the hot water dispenser button pressed. Release the button when you are finished dispensing hot water . When you release the hot water dispenser button make sure the safety switch returns to its original position. SPECIFICATIONS Capacity: 3 or 5 Gallon Water Bottle Chilling Rate: Approx. 2 liters per hour Heating Rate: Approx. 5 liters per hour Power Consumption: Cooling -80W Heating -500W CLEANING AND CARING FOR THE DISPENSER IMPORTANT: Maker sure both power switches are turned OFF and UNPLUG the water dispenser before cleaning and draining Cleaning the Dispenser Cabinet The dispenser cabinet can be washed with mild soap and water. Rinse thoroughly with clear water. Cleaning the Condenser Sweep away or vacuum up dust from the condenser coils on the back of the unit. For best results, use a brush specially designed for this purpose. Cleaning the Drip Tray and Grille The dispenser drip tray is not self-draining. To reduce water spotting, the tray and its grille should be emptied, cleaned and wiped dry regularly. Cleaning the Water Tanks The water dispenser tanks need to be cleaned periodically to prevent buildup of mineral deposits that can affect water taste and flow. To clean the water tanks: 1 Remove the water bottle from the bottle supporter. Watch out for water spillage. 2 Drain the water tanks ( see Draining the Dispenser, page 7) 3 Create a solution of one quart of water with either one quart of vinegar or four ounces of lemon juice. Make enough so you can fill the water tank all the way to the top. 4 Pour the solution in the opening at the top of the dispenser. 6 After about one hour, press the hot & cold buttons until no more water comes out of the taps. IMPORTANT: Before use, dispense at least one quart of water from each tap to make sure the cleaning solution is completely removed. Draining the Dispenser IMPORTANT: Put both power switches to the OFF position and UNPLUG the water dispenser before draining. Allow the dispenser to cool overnight before draining to reduce the risk of scalding The dispenser should be drained before cleaning the tanks or if it will not be used for extended periods. 1. Remove the water bottle from the dispenser. 2. Place a bucket beneath the drain plug. The drain plug is located at the rear of the dispenser (see image below). 7. Remove the cap from the drain plug and allow water to drain completely. Replace the cap. 8. Press both dispenser buttons until no more water comes out of the taps. 7 TROUBLESHOOTING TIPS Please check the following troubleshooting tips before calling the customer service line or having the machine repaired. Problem Possible Causes What To Do Water not hot enough or cold enough Dispenser is unplugged Push the power plug completely into the outlet and make sure that the applicable switches are set to the ON position The circuit breaker has been tripped Reset the circuit breaker All the water in the water tank has been used Wait 1 hour for the dispenser to heat or cool a new batch of water Water dispenser does not work Empty water bottle Replace with new bottle of water Mineral deposits are clogging the tanks See Cleaning and Caring for the Dispenser (page 7) No water coming out of the cold water faucet Ice has formed in the cold water supply pipe Turn off the green cooling power switch at the back of the unit for around 4 hours to let the ice melt Water bottle is warm or hot Crack or pin hole in bottle Low water level in the bottle Replace with a new bottle of water Replace with a new bottle of water Water dispenser leaks from the outside Crack or pin hole in bottle Replace with a new bottle of water Water dispenser is noisy Water Dispenser is on an uneven surface Make sure the water dispenser is installed on a flat and level floor which is strong enough to support it when fully loaded Bottle making a gurgling noise as water fills the tanks This is normal 8 ONE YEAR LIMITED WA...
Эта инструкция также подходит к моделям:Диспенсеры - FX-7SB/W (397.7 kb)