Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Each press switches the repeat mode as follows: 1 - REPEAT 1 ( The repeat indicator is flashing. ) 2 - REPEAT ALL ( The repeat indicator is steadily on. ) 3 - NORMAL PLAYBACK Up to 20 tracks can be programmed for disc play in any order. Be sure to press the “STOP” button before use. 1. Press the “PROGRAM” button, the display will show “01” and flash. 2. Select desired track by using the “SKIP +” or “SKIP -” button. 3. Press the “PROGRAM” button again to confirm desired track into the program memory. 4. Repeat step 2 and 3 to enter additional tracks into the program memory. 5. When all the desired tracks have been programmed. Press the “PLAY / PAUSE” button to play the disc in the order you have programmed and the program indicator flashes. 6. Press the “STOP” button twice to terminate programmed play and the program indicator will turn off. PROGRAM REPEAT 1 REPEAT ALL NORMAL PLAYBACK 14. PHONO OPERATION GENERAL OPERATION Replacement of a worn stylus can be easily accomplished as follows: 1. To remove the old stylus, pull out the stylus assembly in direction shown, holding the head shell with your other hand. 2. Then install the new stylus by pushing it gently into the cartridge ( hold by the edge to prevent damage to stylus. ) until it clicks into place. Notes: Remove the stylus protector. Be sure that the tone arm is detached from the tone arm rest before operation and resecured again afterward. 1. Set the “FUNCTION” selector to “PHONO” mode. 2. Set the “SPEED” selector to the proper speed depending on the record to be played. 3. Place the record on the platter. 4. Lift the tone arm from the rest and slowly move it to the record side. The platter will begin to rotate. 5. Place the tone arm on the desired position. 6. Adjust the “VOLUME” control to the desired level. 7. At the end of the record, the platter will automatically stop rotation. Lift the tone arm from the record and return it to the rest. 8. To stop manually, lift the tone arm from the record, and return it to the rest. Notes: As some kind of record the auto -stop area was out of the unit setting, so it will stop before the last track finish. In the case, set the “AUTO -STOP” selector to “OFF” mode, then it will run to the end of the record but will not stop automatically. ( Set the “FUNCTION” selector to “OFF” mode or set the “AUTO -STOP” selector to “ON” mode to stop the playback. ) Put back the tone arm to the rest. STYLUS REPLACEMENT 1 2 14. PHONO OPERATION GENERAL OPERATION Replacement of a worn stylus can be easily accomplished as follows: 1. To remove the old stylus, pull out the stylus assembly in direction shown, holding the head shell with your other hand. 2. Then install the new stylus by pushing it gently into the cartridge ( hold by the edge to prevent damage to stylus. ) until it clicks into place. Notes: Remove the stylus protector. Be sure that the tone arm is detached from the tone arm rest before operation and resecured again afterward. 1. Set the “FUNCTION” selector to “PHONO” mode. 2. Set the “SPEED” selector to the proper speed depending on the record to be played. 3. Place the record on the platter. 4. Lift the tone arm from the rest and slowly move it to the record side. The platter will begin to rotate. 5. Place the tone arm on the desired position. 6. Adjust the “VOLUME” control to the desired level. 7. At the end of the record, the platter will automatically stop rotation. Lift the tone arm from the record and return it to the rest. 8. To stop manually, lift the tone arm from the record, and return it to the rest. Notes: As some kind of record the auto -stop area was out of the unit setting, so it will stop before the last track finish. In the case, set the “AUTO -STOP” selector to “OFF” mode, then it will run to the end of the record but will not stop automatically. ( Set the “FUNCTION” selector to “OFF” mode or set the “AUTO -STOP” selector to “ON” mode to stop the playback. ) Put back the tone arm to the rest. STYLUS REPLACEMENT 1 2 15. SPECIFICATIONSGENERALPower supply : AC 230V ~ 50Hz Frequency range : AM 525 - 1615kHz FM 87.5 - 108MHz (Specification subjects to be changed without notice.) 15. SPECIFICATIONSGENERALPower supply : AC 230V ~ 50Hz Frequency range : AM 525 - 1615kHz FM 87.5 - 108MHz (Specification subjects to be changed without notice.) 16. PLUS D’INFORMATIONS MODELE: 2750G Tourne-disque avec lecteur CD, radio et haut-parleurs MESURES DE SECURITE AVERTISSEMENT RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION: POUR REDUIRE LE RISQUE DE CHOC ELECTRIQUE, NE PAS RETIRER LE BOITIER (OU L’ARRIERE DU BOITIER). CET APPAREIL NE CONTIENT AUCUNE PIECE REPARABLE PAR L’UTILISATEUR. EN CAS DE PROBLEME, FAITES APPEL AU PERSONNEL D’UN SERVICE QUALIFIE. Le point d’exclamation dans un triangle equilateral avertit l’usager de la presence de consignes importantes pour le fonctionnement ou l’entretien (maintenance) dans la documentation qui accompagne l’appareil. Ce symbole eclair fleche, dans un triangle equilateral, avertit...