Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
• Keep your stainless steel unit looking new by cleaning with a good quality all-in-one stainless steel cleaner/ polish on a monthly basis. For best results use Claire® Stainless Steel Polish and Cleaner, which can be purchased from U-Line Corporation (P/N 173348). Comparable products are acceptable. Frequent cleaning will remove surface contamination that could lead to rust. Some installations may require cleaning on a weekly basis. • Do not clean with steel wool pads. • Do not use cleaners that are not specifically intended for stainless steel on stainless steel surfaces (this includes glass, tile and counter cleaners). • If any surface discoloring or rusting appears, clean it quickly with Bon-Ami® or Barkeepers Friend Cleanser® and a non-abrasive cloth. Always clean in the direction of the grain. Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems. • Using abrasive pads such as Scotchbrite™ will cause the graining in the stainless steel to become blurred. • Rust that is not cleaned up promptly can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible. Interior Cleaning (As Required) • Disconnect power to the unit. Clean the interior and all removed components using a mild non-abrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. Rinse the interior using a soft sponge and clean water. • Do not use any solvent-based or abrasive cleaners. These types of cleaners may transmit taste to the interior products and damage or discolor the interior. Maintenance Proper maintenance of your U-Line product will ensure efficiency, top performance and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets or other special considerations. Defrosting Automatic (Cycle) Defrost Models Automatic defrost models do not produce frost in normal operating conditions. However, a frost pattern may be noticed on the interior walls if the unit is repeatedly opened in a high heat or high humidity location. If this frost pattern does not clear within 24 hours, your unit will require manual defrosting. WARNING DO NOT use any type of electrical heating device, ice pick, knife or other sharp instrument to defrost; this could damage the inner lining or refrigeration system and void the warranty. IMPORTANT The drain pan was not designed to capture the water created when manually defrosting. To prevent water from overflowing the drain pan, place towels or other absorbent materials over the interior drain trough, under the evaporators (Figure 11, 1), before defrosting. Figure 11 7 Cleaning and Maintenance ULIN_0235_A 1 14 2275DWRWS, 2275DWRWOL To defrost: 1. Turn unit off. 2. Remove all products from the interior and open the drawer(s) (2" (5 cm) minimum). 3. Allow the frost to completely melt naturally. Clean the interior and all removed components using a mild nonabrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. NOTE: DO NOT use any solvent-based or abrasive cleaners. They will discolor or damage the interior. 4. Dampen a soft sponge or non-abrasive cloth in clean water and wipe down the cabinet interior and removed components to remove any detergent residue. Rinse the sponge or cloth in clean water and repeat as necessary until the cabinet and components are clean. 5. When the interior is dry, turn unit back on. Condenser Cleaning Interval - Every Three Months To maintain operational efficiency, keep the front grille free of dust and lint and clean the condenser every three months. Depending on environmental conditions, more or less frequent cleaning may be necessary. WARNING Disconnect electric power to the unit before cleaning the condenser. To remove and replace the grille for access to the condenser fins, follow this procedure: Figure 12 1. Disconnect electrical power to the unit. 2. Loosen two screws (Figure 12, 1) completely. NOTE: Screws are held in the grille by o-ring retainers, and will not come free of the grille. 3. Remove the grille. WARNING DO NOT touch the condenser fins. The condenser fins are SHARP and can be easily damaged. CAUTION DO NOT use any type of cleaner on the condenser unit. 4. Clean the condenser coil (Figure 12, 2) using a soft brush with a “combing” action or vacuum cleaner. Do not touch the condenser coil. 5. Position the grille to align the mounting screws with the holes in the cabinet. 6. Secure, but do not over-tighten both grille screws. 7. Reconnect power to the unit. Leveling Figure 13 1. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown (Figure 13). Figure 14 2. If the unit is not level, adjust the feet on the corners of the unit as necessary (Figure 14). 3. Check the levelness after each adjustment and repeat the previous steps u...
Эта инструкция также подходит к моделям:Диспенсеры - 2275DWRWOL (2.3 mb)