Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
In this case contact store where stroller was purchased for more help. • Check that Carrycot attachment devices are correctly engaged before use. • Always remove Carrycot before folding stroller. 3Preparing your Stroller to fit the Carrycot 3Preparing your Stroller to fit the Carrycot Before you can attach the Carrycot to your stroller you will need to remove the fabric sunhood and seat on your stroller. Removing the Sunhood 1. Standing beside your stroller and using a reasonable degree of force, pull the sunhood support wire towards you (by about 50mm/2in). 2. Remove support wire W from sunhood bush J on the side nearest to you. 3. Unfasten sunhood domes that attach the sunhood to stroller frame and to stroller seat back. W J Removing the Seat 1. Unfasten domes on seat that attach to frame. 2. Urban (Jungle) Only: unfasten strap underneath seat at point A. 3. Terrain Only: remove seat support wire from stroller frame at C and D. Push seat forward, then slide fabric off seat support wire. A CD ENGLISH 4 Preparing your Stroller (continued) 4 Preparing your Stroller (continued) IMPORTANT INFORMATION FOR DOUBLE AND ››› TRIPLE STROLLERS If you have a double or triple stroller you will need to remove the centre metal bars of the frame to release the domed fabric. You may then need to reattach the metal bars without the fabric, depending on whether you are attaching a Double or a Twin Carrycot. See chart below. How to remove the centre bar(s) 1. Terrain only: undo seat base nut with a spanner at point F and remove hinge pin from seat base. 2. Urban and Terrain models: unfasten wing nut at point G and remove centre bar at both ends (points G and H). Centre bar Seat base Heel rest H F G Double Stroller Frame Triple Stroller Frame Twin Carrycot No centre bar No centre bar on side attaching Twin Carrycot. Centre bar remains on side not accommodating Twin Carrycot. Double Carrycot Centre bar required. Remove hammock fabric from seat you wish to replace with Carrycot. Centre bar required. Remove hammock fabric from seat you wish to replace with Carrycot. Double Carrycot can only be fitted to outside seat positions. 5Fitting your Carrycot to your Stroller 5Fitting your Carrycot to your Stroller Mountain Buggy offer a range of carrycot and stroller combinations, so please choose the instructions you need to follow from the list below based on which carrycot model you are wanting to attach to which stroller. Single Stroller Double Stroller Triple Stroller Single Carrycot Confi guration 1 Double Carrycot Confi guration 2 Confi guration 2 Twin Carrycot Confi guration 1 Confi guration 2 Instructions for Configuration 1 are located on pages 6-7 Instructions for Configuration 2 are located on pages 8-10 Examples of Carrycot combinations Double Stroller with Double Stroller with Triple Stroller with 2 Double Carrycots Twin Carrycot 1 Double and 1 Twin Carrycot ENGLISH 6 Configuration 1 Instructions 6 Configuration 1 Instructions PLEASE FOLLOW THESE INSTRUCTIONS IF YOU ››› ARE FITTING: a: a Single Carrycot to a Single Stroller b: a Twin Carrycot to a Double Stroller Fitting the Snap Locks to the Carrycot Preparation You will need to have all components on the parts list shown to fit Carrycot to your stroller. Have a look at sides of Carrycot. There are three holes on each side of Carrycot to allow snap locks to be fitted. Configuration varies depending on the Mountain Buggy model you have. • Two snap locks are fitted to each side of Carrycot. The unused hole can be fitted with the spare screw and cover button. How to fit the Snap Locks 1. Place one snap lock over hole A. Make sure it is aligned correctly with the hole in Carrycot. 2. Using Allen key, rotate screw in snap lock in clockwise direction until screw is tight. Snap lock will still be able to rotate but is firmly attached. 3. Connect second snap lock according to model directions below. 4. Repeat on other side. For Urban (Jungle) models 5. Fit second snap lock to position B. 6. Fit small screw and cover button to hole C. For Terrain Models 5. Fit second snap lock to position C. 6. Fit small screw and cover button to hole B. A 2 x screws 2 x cover buttons Allen key Carrycot PARTS LIST 4 x snap locks A B C URBAN TERRAIN C B A 7Configuration 1 Instructions (continued) 7Configuration 1 Instructions (continued) Fitting the Carrycot to the Frame 1. Ensure snap locks are rotated so screw holes are on top. 2. Open snap locks. 3. Place Carrycot onto Buggy frame. Confirm positioning as pictured below. TERRAIN URBAN ENGLISH . . X Y sunhood joint Place snap lock X directly above sunhood joint X Y tube joint Place snap lock Y directly above tube joint 4. Push snap locks firmly down flat, making sure you hear the lock ‘click’, indicating they are fully locked. Fitting the Feet to the Carrycot 1. Take one foot and place provided screw through hole in narrow end of foot. 2. Screw whole unit into one of the 4 holes located on bottom of Carrycot. 3. Ensure foot is screwed tightly. 4. Rep...