Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Step 3. Front Wheel Assembly Turn stroller upright onto its rear wheels, then tip stroller back so the handlebar is down on the ground and the front fork is up.Attach the front wheel by loosening the exterior lock nut on each side of the front wheel far enough to allow the axle and tab washer to slide into the front fork.The tab washer’s tab should be inserted into the small hole on the outside of the front fork (Figure C).Center the wheel between the front C fork.Tighten the nuts with an adjustable wrench. IMPORTANT: The alignment of the front wheel determines if the stroller will roll straight, or pull to the right or left during use.In the event you notice the stroller pulling to one direction, loosen front axle nuts, point the front wheel in the opposite direction the stroller is pulling, ensure the tab washers are seated in the holes and tighten the nuts. If you need help making this adjustment, please call our Customer Service department for assistance. WARNING: The interior jam nuts are factory installed and do not need adjustment. B Rear Wheel Rear Brake Lock Nut Tab Washer Adjustment Hole for Tab Washer Locknut Front Wheel Step 4. Front Fender Assembly Insert the #8 – 11.2" screws into the holes located on the front support between the front forks.Align the 2 holes on the bottom side of the fender with the screws and tighten with a Phillips screwdriver.Note:The Double EZStrider has 4 screws (Figure D). Step 5. Canopy Positioning The canopy has adjustable positions.Pull the canopy down to the desired position. Step 6.To Attach Wrist Strap Place strap on top of handle bar.The wrist strap has different sized loops.The large loop will go on your wrist, the small loop will be on handlebar.Slide end with large loop through the small loop, then grasp the end with the large loop and pull strap to tighten on handlebar. D #8 – 11.2" Screws Double has 4 Holes/Screws WARNING: Whenever child is in stroller always use the wrist strap.Before you remove the wrist strap from your wrist make sure you first engage the rear brakes. Congratulations – assembly is now complete! 3 Use Instructions To close/fold stroller: WARNING: Always remove child from stroller before folding. Pull the seat/seats forward, locate the plastic latches on the side of the stroller frame.Using one hand on each lever, pull the levers from the lower bar.The stroller will automatically begin to fold, the front wheel will fold under frame and the handle will fold backwards ( Figure E). NOTE: The stroller will be easier to fold if the seats are not in the recline position. If the seats are in the recline position please pull forward. To open stroller: Grasp handle with one hand and pull up on the front axle mount with your other hand. Lock both plastic latches onto the lower frame (Figure F). E Latches Pull Seat Forward When Folding F Latches on Both Sides Double EZ Strider Single EZ Strider 4 To engage rear brakes: Step lightly on the levers next to the rear wheels until the cogs of the brakes engage the cogs of the wheel.Repeat on other side.To release brake, lift levers using your toe until cogs disengage (Figure G). Proper use of seat belts & shoulder straps: WARNING: Avoid Serious Injury. Always use T adjust the recline position, adjust the slide on T place seat in upright position, push seat forward and reconnect buckle located on back of seat. T fully recline, unhook buckle on back of the seat. recline seat: 3. Slide waist straps through lower loops of shoul- Lder straps, bring lap belt ends together and clip into place around child’s waist. Adjust waist and shoulder straps for snug fit (Figure H). 2. When child is seated, place shoulder straps er the child’s shoulders. 1. Place child in seat. Make sure T-shield is seat belts. T(Figure I). the strap. between the child’s legs. WARNING: Child may slip into leg openings and strangle.Never use in a reclined carriage position unless T-shield and shoulder strap have been readjusted to the new seat position. G Rear Brakes H Shoulder Straps Shoulder Strap Adjustment Slides Waist Buckle Adjustment T-Shield Waist Belt Waist Belt I 5 Care and Maintenance Check fasteners After one hour of use, check all fasteners to make sure they are secure.Adjust if necessary. Periodically check the stroller to ensure that it is in good operating condition. To adjust the stroller from pulling to the left or right (not rolling straight): Loosen the front axle nuts and check to see that the tab washers are inserted in the holes of the front fork. Point the front wheel forward or in the opposite direction the stroller is pulling, then tighten the nuts with an adjustable wrench. NOTE: Sometimes it is a very slight adjustment to eliminate the pulling and this step may need to be repeated. To clean seat and canopy: If light cleaning is required, use a soft cloth with warm water and mild soap then air dry.Do not put into washing machine. Do not put in dryer.DO NOT BLEACH. To clean frame: Wipe using a soft cloth with warm wa...