Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
WARNING This unit is not designed for use with a charcoal grill. ! Either an interior or exterior blower or in-line blower may be used with this hood. The Best by Broan WPD29M Series must be installed with blower models P12D, ILB11, EB12 or EB15 only. Other blowers cannot be substituted. (Blowers sold separately.) Plan where and how the ductwork will be installed. If installing ILB11 in-line blower, discard its rough-in plate. Refer to instructions packed with in-line blower and follow steps 1 up to 6, 8, 9, 10, 11, 13 and up of this manual. Install 10” round galvanized steel ductwork, elbows and roof or wall cap for the type of blower you are installing. Use metal duct tape to seal duct joints. The minimum hood distance above cooktop must not be less than 30’’. A maximum of 36” above cooktop is highly recommended for best capture of cooking impurities. Distances over 36” are at the installer and users discretion. Run power cable to installation location. 18" WALL CAP 30" TO 36" ABOVE COOKING SURFACE 17 11/16" to TOP OF WOOD MOUNTING STRIP HOOD OPTIONAL DECORATIVE FLUE or SOFFIT 9" x 18" to 10" ROUND TRANSITION INCLUDED HH0073A ROOF CAP 10" ROUND DUCT 10" ROUND ELBOW EXTERIOR BLOWER HH0074A 18" 30" TO 36" ABOVE COOKING SURFACE 17 11/16" to TOP OF WOOD MOUNTING STRIP HOOD OPTIONAL DECORATIVE FLUE or SOFFIT 9" x 18" to 10" ROUND TRANSITION INCLUDED 10" ROUND DUCT 10" ROUND ELBOW HH0075A 30" TO 36" ABOVE COOKING SURFACE HOOD WALL CAP ROOF CAP IN-LINE BLOWER 10" ROUND DUCT WARNING The power cable must be a GFCI protected branch circuit. ! MODEL P12D DUAL INTERIOR MODEL EB12 OR EB15 EXTERIOR MODEL ILB11 IN-LINE BLOWER BLOWER TYPICAL DUCTWORK BLOWER TYPICAL DUCTWORK TYPICAL DUCTWORK - 4 Remove the installation kit from inside the hood. Make sure that the following items are included: - Wood strip (screwed on back of hood) - Installation manual - Transition (9’’ x 18’’ to 10’’ round) - Accessories including: • Baffle filters (3) • Shielded halogen lights (GU10 type base, 120 V, 50 W) (4 for a 42” width hood, 6 for a 54” width hood) • Bag of parts including: (3) waterproof wire connectors, (2) wire clamps, (4) flat head screws #10-2’’, (8) screws #8 x 5/8’’, (8) screws #8 x 3/8’’, (2) wall anchors, (2) washers 3/16’’ ID x 3/4’’ OD Parts sold separately: - Interior blower Model P12D. - In-line blower assembly ILB11, including transitions and rough-in plate. Discard the rough-in plate. - Exterior blower assembly EB12 or EB15 (all include rough-in plate). Discard the rough-in plate. - Duct, elbows, dampers, wall and roof caps. Refer to page 3 for a complete list of venting options and model numbers. - Optional decorative flue AEWPD Series. - 5 - 2. PREPARE THE INSTALLATION CAUTION When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. 3. REMOVE THE FILTERS AND THE GREASE DRIP RAIL A. Remove tape on filters. Remove filters from hood and set aside. NOTE: It is recommended to start with the central one. B. Remove tape on grease drip rail (1). Lift out grease drip rail and set aside. NOTE: When tape is removed in the position as shown at side, drip rail will possibly fall out due to gravity. HD0182 1 4. REMOVE THE PAN Using a Phillips no. 2 screwdriver, remove the screws retaining the pan (shaded part on illustration beside) to the hood. Remove the pan and set aside. HD0183 RETAINING SCREWS LOCATION 5. REMOVE THE TRANSITION RRETAININGETAINING SCREWSSCREWS ANDAND WASHERSWASHERS LOCATIONLOCATION HD0191 Using a Phillips no. 2 screwdriver, remove and discard both screws and washers retaining the transition to the hood. Remove the transition and the wood mounting strip (on back of hood) and set aside. 6. INSTALL WOOD MOUNTING STRIP HD0192A Measure and mark a level line on wall above cooktop location for the wood mounting strip (see illustration on page 4). Center the wood mounting strip over location. See illustration shown at side. Use #10, 2’’ flat head screws to secure the mounting strip to the drywall. Make sure to hit the wall studs. CAUTION Due to the weight of this hood, ensure that the wood strip is attached to every available stud, not into the drywall alone. 1.Drywall 4.Wall anchor location 2.Wood mounting strip 5.Backof hood outline 3.Flat head screw 6.Wallstuds 7. SELECT BLOWER OPTION (EXTERIOR OR INTERIOR) INTERIOR BLOWER: Follow all subsequent steps of this manual. EXTERIOR BLOWER: Discard the exterior blower rough-in plate. Refer to instructions packed with exterior blower and follow steps 8 to 11, 13 and up of the present manual. - 6 8. CONNECT WIRING WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. ! ALL INSTALLATIONS: Remove the hood wiring box cover. Install wire clamp(s) on back side of the hood. Position the...