Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
•Vytahnete po kazdem pouziti zastrcku ze zasuvky a nechte zehlicku vychladnout. Otrete zehlici plochu vlhkym hadrem, na ktery muzete podle potreby nanest nepenivy cistici prostredek. Kryt ocistete vlhkym hadrem. VYPRAZDNENI A ULOZENI • Zajistete, ze bude zehlicka odpojena od elektricke site. •Odstrante zbytky vody tim, ze zehlickou lehce zatresete. •Dbejte po kazdem pouzitim na to, aby voda nezustala v nadrzce pristroje. • Zehlicku nasadte na ochranny kryt (OCHRANNY KRYT NEPOUZIVEJTE PRI ZEHLENI) • Kabel ovinte okolo navijeni kabelu na zadni strane zehlicky. • Zehlicku ukladejte vzdy ve vodorovne poloze na pevnem povrchu nastojato a chranenou krytem. Nechte zehlicku zcela vychladnout, nez ji odstavite k ulozeni. Prohlaseni o Shodnosti My, Komperna. Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, timto prohlasujeme, ze tento vyrobek souhlasi s nasledujicimi smernicemi EU: Nizkonapetova smernice: Elektromagneticka slucitelnost: podle pouzitych norem: 73/23/EEC 89/336 EEC EN 55014-2:1997+A1 EN 55014-1:2000+A1 EN 61000-3-2:2000 EN 61000-3-3:1995+A1 Typ/nazev stroje: KH 2203 Bochum, 31.05.2003 Hans Komperna. - vedouci obchodu STEAM AND DRY IRON SAFETY INSTRUCTIONS To reduce the risk of electrical shock or fire, resulting in injury or damage, take the following precautions: • Do not use the iron near or under curtains or other inflammable materials and never leave it unattended while connected or on an ironing board. •Use this iron only for its intended use. In case of unintended use there is danger of injury for the user and damage on the device. •To protect against a risk of electric shock, do not immerse the iron in water or other liquids. • The iron should always be turned to MIN before plugging or unplugging from outlet. Never pull the cord to disconnect from outlet to avoid damaging the cord. Instead, grasp plug and pull to disconnect. •Do not allow the cord to touch hot surfaces, it could be damaged. • Let the iron cool completely before putting it away to prevent fire. •Put the iron on the storage cover and loop the cord around iron when storing. •Always disconnect the iron from the electrical outlet when filling it with water or emptying it and when the iron is not in use. •Do not operate an iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron; take it to the customer service for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used. •Close supervision is necessary if the iron is being used by or near children, they cannot realize the risks that could result from using electrical appliances. • Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down – there may be hot water in the water tank. •All repair work should be carried out by an approved service center. • Push the steam button a few times and lightly shake the iron after use to ensure all water is drained. The remaining moisture will evaporate if you then plug in the cord and heat iron for a few moments. • This iron is intended for home use only. •Keep these instructions in a safe place. Lervia KH 2203 PARTS IDENTIFICATION . Cord Protector / Power Cord . Water Tank . Temperature Control Knob . Calc Clean Button . Sole Plate . Heating Light (green)/ Auto Shut Off Light (orange) . Steam Burst Button . Spray Button . Steam Control Gear . Water Tank Lid . Spray Nozzle . Storage Cover . Measuring Cup HOW TO USE YOUR IRON BEFORE FIRST USE •Before using the iron for the first time, check if the voltage rating on the base plate corresponds to the mains voltage in your home. •Remove the storage cover, sticker or any protective items from the soleplate. •It is important to remove any residues of the polishing compound, used on the soleplate, which may have lodged in the steam vents. Using the measuring cup supplied, pour water into the iron up to the MAX line. Clean the steam vents by using “Calc Clean” system. (See using the Calc Clean Button). When finished, wipe the soleplate with an old cloth. Cotton swabs may be used to clean and dry the steam vents. •Some parts of the iron have been slightly greased and as a result the iron may smoke slightly when switched on for the first time. After a short while, however, this will cease. •Normal tap water can usually be used for ironing. But if you live in a hard water area we recommend to use distilled water to insure optimum performance of your iron. CONTROLLING THE TEMPERATURE Turn your temperature control knob to the position you desire according to the following fabric indications: nylon silk wool cotton linen Calc Clean Lervia KH 2203 Lervia KH 2203 IRONING TIPS Sort the articles to be ironed according to the fabric. Ironing instructions are usually stitched onto an inside seam of a garment and these should be followed at all times. Start your ironing with the fabrics requiring the lowest heat setting. If...