Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
•Note that the DST/Standard Time setting affects only the currently displayed city code. Other city codes are not affected. •Note that you cannot switch between Standard Time and Daylight Saving Time while GMT is selected as the city code. Countdown Timer The countdown timer can be set within a range of one minute to 60 minutes. An alarm sounds when the countdown reaches zero. The countdown timer also has an auto-repeat feature and a progress beeper that signals the progress of the countdown. •All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C. Configuring the Countdown Timer The following are the settings you should configure before actually using the countdown timer. Countdown start time; Auto-repeat on/off; Progress beeper on/off •See “To configure the countdown timer” for information about setting up the timer. Auto-repeat When auto-repeat is turned on, the countdown automatically restarts from the countdown start time when it reaches zero. If left running, the countdown is repeated a total of eight times, after which it stops automatically. When auto-repeat is turned off, the countdown stops when it reaches zero and the display shows the original countdown start time. •Pressing D while an auto-repeat countdown is in progress pauses the current countdown. You can resume the auto-repeat countdown by pressing D, or you can press A to reset to the countdown time starting value. Countdown Timer Beeper Operations The watch beeps at various times during a countdown so you can keep informed about the countdown status without looking at the display. The following describes the types of beeper operations the watch performs during a countdown. Countdown End Beeper The countdown end beeper lets you know when the countdown reaches zero. •When the progress beeper is turned off, the countdown end beeper sounds for about 10 seconds, or until you press any button to stop it. •When the progress beeper is turned on, the countdown end beeper sounds for about one second. Progress Beeper When the progress beeper is turned on, the watch uses beeps to signal countdown progress as described below. •Starting from five minutes before the end of the countdown, the watch emits four short beeps at the top of each countdown minute. •30 seconds before the end of the countdown, the watch emits four short beeps. •The watch emits a short beep for each of the last 10 seconds of the countdown. •If the countdown start time is six minutes or greater, the watch emits a short beep for each second of the final 10 seconds before the five-minute point is reached. Four short beeps are emitted to signal when the five-minute point is reached. Current time for the selected city code City code SecondsMinutes Setting Start Time Auto-repeat Progress Beeper Screen Button Operation Use D (+) and B (–) to change the setting. •You can set a start time in the range of 1 to 60 minutes in 1-minute increments. Press D to toggle auto-repeat on ( displayed) and off ( displayed). Press D to toggle the progress beeper on (ON) and off (OF). 1/100 second SecondsMinutes To configure the countdown timer 1. While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the current countdown start time starts to flash, which indicates the setting screen. •If the countdown start time is not displayed, use the procedure under “To use the countdown timer” to display it. 2. Press C to move the flashing in the sequence shown below to select other settings. Start Time Auto-repeat Progress Beeper 3. When the setting you want to change is flashing, use B and D to change it as described below. 4. Press A to exit the setting screen. •You can also perform steps 1 and 2 of the above procedure whenever you need to view the current auto-repeat and progress beeper settings. To use the countdown timer Press D while in the Countdown Timer Mode to start the countdown timer. •The countdown timer operation continues even if you exit the Countdown Timer Mode. •Press D while a countdown operation is in progress to pause it. Press D again to resume the countdown. •To completely stop a countdown operation, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value. Stopwatch The stopwatch lets you measure elapsed time, split times, and two finishes. •The display range of the stopwatch is 59 minutes, 59.99 seconds. •The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. •The stopwatch measurement operation continues even if you exit the Stopwatch Mode. •Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement. •All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. To measure times with the stopwach Elapsed Time Start Stop Re-start Stop Clear Start Split (SPL displayed) Split release Stop C...
Эта инструкция также подходит к моделям:Часы - 2759 (815.9 kb)