Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
•The watch receives the calibration signal for four to 14 minutes everyday when the time in the Timekeeping Mode reaches each of the calibration times. Avoid performing any button operation within 14 minutes before or after any one of the calibration times. Doing so can interfere with correct calibration. •Remember that reception of the calibration signal depends on the current time in the Timekeeping Mode. To perform manual receive 1. Place the watch on a stable surface so its 12 o’clock side is facing towards a window. 2. In the Timekeeping Mode, hold down Afor about two seconds until the watch beeps. 3. The stopwatch second hand will move to R (READY) to indicate that the watch is setting up for time calibration reception. •The second hand will move to W (WORK) and stay there while actual reception is in progress. •The hour and minute hands continue to keep time normally. •Time calibration signal reception takes from four to seven minutes, but in some cases it can take up to 14 minutes. Take care that you do not perform any button operations or move the watch during this time. •If reception is successful, the second hand will move to Y (YES). One minute later, the hands will move to the correct time. W (WORK) R (READY) Y (YES) N (NO) Note •To interrupt a receive operation and return to the Timekeeping Mode, press any button. •If reception is not successful, the stopwatch second hand will move to N (NO). One minute later, the stopwatch second hand will resume normal operation, without any adjustment of the hand setting. •If the stopwatch second hand is pointing to Y (YES) or N (NO), you can return to the Timekeeping Mode by pressing any button. Viewing the Latest Signal Reception Results You can use the Receive Result Mode to check if signal reception was performed correctly. To check the latest signal reception results 1. In the Timekeeping Mode, press A. •If the watch was able to perform a successful signal receive operation since midnight, the stopwatch second hand will move to Y (YES). If the watch has been unable to receive any signal successfully, the second hand will move to N (NO). •The watch will return to the Timekeeping Mode after five seconds. •The current receive result is cleared when the first auto receive operation is performed on the following day. This means Y (YES) indicates successful signal reception since the start of the current day. •If you adjust the time or date setting manually, the second hand will move to N (NO). Signal Reception Troubleshooting Check the following points whenever you experience problems with signal reception. •For further information, see “Important!” under “Time Calibration Signal Reception” and “Radio-controlled Atomic Timekeeping Precautions”. Stopwatch The stopwatch lets you measure elapsed time,. •The display range of the stopwatch is 59 minutes, 59.99 seconds. •Entering the Stopwatch Mode causes the second hand, the stopwatch minute hand and stopwatch 1/20 second hand to move to the 12 o’clock position. •The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. •The stopwatch measurement operation continues even if you exit the Stopwatch Mode. •All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. Stopwatch 1/20 second hand * This hand rotates and indicates the second count during the first 60 seconds. Second hand Stopwatch minute hand Stopwatch 1/100 second To measure elapsed time 1. Press Bto start the stopwatch. 2. Press Bto stop the stopwatch. •You can resume the measurement operation by pressing Bagain. •The 1/20 second hand rotates during the first 60 seconds only, and then stops. When elapsed timing is stopped (by pressing B), this hand jumps to the 1/20 second indication (which is kept internally). 3. Check the elapsed time. •Press A to reset the stopwatch. Dual Time The Dual Time Mode lets you view the current time in 29 time zones around the world. •Time zones are indicated on the digital display by their GMT differential values. •For full information on time zones, see the “Time Zone Table”. •The watch will perform a signal receive operation even if it is in the Dual Time Mode when a calibration time is reached. If this happens, the Dual Time Mode time settings will be adjusted in accordance with the current time in the Timekeeping Mode’s Home Time Zone. •All of the operations in this section are performed in the Dual Time Mode, which you enter by pressing C. GMT differential value(+1.0) To view the time in another time zone While in the Dual Time Mode, press B to scroll eastward through time zones. •When you release B, the hands will move to the current time in that time zone after about one second. •If the current time shown for a time zone is wrong, check the Timekeeping Mode time setting and your Home Time Zone setting, and make the necessary changes. Home Time Zone Transmitter Frequency –5.0 (DST –4.0) –6.0 (DST –5.0) –7.0 (DST –6.0) –8.0 (DST –...
Эта инструкция также подходит к моделям:Часы - MO0701-EB (587.75 kb)
Часы - MO0701-EB (587.75 kb)
Часы - MO0701-EB (587.75 kb)
Часы - MO0701-EB (587.75 kb)