Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
In the case of the snooze alarm, the alarm operation is performed a total of seven times, every five minutes, or until you turn the alarm off. • Pressing any button stops the alarm tone operation. • Performing any one of the following operations during a 5-minute interval between snooze alarms cancels the current snooze alarm operation. Displaying the Timekeeping Mode setting screen Displaying the snooze alarm setting screen To test the alarm In the Alarm Mode, hold down B to sound the alarm. To turn an alarm on and off 1. In the Alarm Mode, use D to select an alarm. 2. Press B to toggle it on and off. • Turning on a one-time alarm (AL1, AL2, AL3, AL4) displays the alarm on indicator on its Alarm Mode screen. Turning on the snooze alarm (SNZ) displays the alarm on indicator and snooze alarm indicator on its Alarm Mode screen. • In all modes, the alarm on indicator is shown for any alarm that is currently turned on. When the snooze alarm is on, the snooze alarm indicator is displayed in all modes. • The alarm on indicator flashes while the alarm is sounding. • The snooze alarm indicator flashes during the 5-minute intervals between alarms. To turn the Hourly Time Signal on and off 1. In the Alarm Mode, use D to select the Hourly Time Signal (SIG). 2. Press B to toggle it on (Hourly Time Signal on indicator displayed) and off (Hourly Time Signal on indicator not displayed). • The Hourly Time Signal on indicator is displayed in all modes when the Hourly Time Signal is turned on. Alarm time (Hour : Minutes) Alarm number Home city time AL1 AL2 AL3 SIG SNZ AL4 Module 2688 Hourly time signal on indicator Module 2608 Module 2638 Module 2688 1/100 second Hours Home city time Seconds Minutes D Start Stop Elapsed Time . Re-start Clear D . Stop D .D .B Split Time D Start Split . Split release Clear B . Stop B .D .B Two Finishes D Start Split . Stop Clear B . Split release D .B .B First runner finishes. Display time of first runner. Second runner finishes. Display time of second runner. To measure times with the stopwatch (SPL/ SPL displayed) Backlight The backlight uses an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. The watch’s auto light switch automatically turns on the backlight when you angle the watch towards your face in the dark. • The auto light switch must be turned on (indicated by the auto light switch on indicator) for it to operate. • See “Backlight Precautions” for other important information about using the backlight. To turn on the backlight manually In any mode, press L to illuminate the display for about one second. • The above operation turns on the backlight regardless of the current auto light switch setting. About the Auto Light Switch Turning on the auto light switch causes the backlight to turn on for about one second, whenever you position your wrist as described below in any mode. Note that this watch features a “Full Auto EL Light,” so the auto light switch operates only when available light is below a certain level. It does not turn on the backlight under bright light. Moving the watch to a position that is parallel to the ground and then tilting it towards you more than 40 degrees causes the backlight to turn on. Warning! • Always make sure you are in a safe place whenever you are reading the display of the watch using the auto light switch. Be especially careful when running or engaged in any other activity that can result in accident or injury. Also take care that sudden illumination by the auto light switch does not surprise or distract others around you. • When you are wearing the watch, make sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury. To turn the auto light switch on and off In any mode, hold down L for about two seconds to toggle the auto light switch on (auto light switch on indicator displayed) or off (auto light switch on indicator not displayed). • The auto light switch on indicator is on the display in all modes while the auto light switch is turned on. Battery This watch is equipped with a solar cell and a rechargeable battery (secondary battery) that is charged by the electrical power produced by the solar cell. The illustration shown below shows how you should position the watch for charging. Example: Orient the watch so its face is pointing at a light source. • Note that charging efficiency drops when any part of the solar cell is blocked by clothing, etc. • The illustration shows how to position a watch with a resin band. Auto light switch on indicator Module 2608 Module 2638 Module 2688 Solar cell Stopwatch The stopwatch lets you measure elapsed time, split times, and two finishes. • The display range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds. • The stopwatch continues to run...
Эта инструкция также подходит к моделям:Часы - 2608 (793.01 kb)
Часы - 2688 (793.01 kb)