Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
•The daily alarm and countdown alarm tones continue to sound even if you turn off the button operation tone. To turn the button operation tone on and off In any mode (except when a setting screen is on the display), hold down C to toggle the button operation tone on ( not displayed) and off ( displayed). •Holding down C to turn the button operation tone on or off also causes the watch’s current mode to change. •The mute indicator is displayed in all modes when the button operation tone is turned off. Mute indicator EL backlight 2 Operation Guide 3164/3250 Mode indicator Minutes To select a timekeeping display style 1. In the Timekeeping Mode, hold down A until the seconds start to flash. This is the setting screen. 2. Press C seven times to display the Active Display on/off screen. 3. Use D to turn off (OF ) Active Display. •You cannot select the timekeeping display style while Active Display is turned on. 4. Press A to exit the setting screen. 5. In the Timekeeping Mode, press A to cycle through the available timekeeping display styles (Style 1 through Style 5), until the one you want is displayed. •Displaying the setting screen while Style 6 is displayed and turning off Active Display will change the display style to Style 2 automatically. Countdown T imer The countdown timer can be set within a range of one to 60 minutes. An alarm will sound when the countdown reaches zero. •The initial factory default setting is one minute (01min ). •The countdown operation continues even if you exit the Countdown Timer Mode. •All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C. To set the countdown start time In the Countdown Timer Mode, press A to increase the countdown start time (minutes). •You can set the countdown start time within the range of one minute (01min ) to 60 minutes (60min ), in one-minute increments. •Holding down A will increase the countdown start time at high speed. To perform a countdown timer operation In the Countdown Timer Mode, press D to start the countdown. •When the countdown reaches zero, the alarm tone will sound for 10 seconds or until you stop it by pressing any button. The countdown time will reset automatically to its starting value after the alarm stops. •In addition to the alarm tone, a Flash Alert operation will be performed when the countdown reaches zero. The Flash Alert operation will continue for 5 seconds or until you stop it by pressing any button. •Press D while a countdown operation is in progress to pause it. Press D again to resume the countdown. •To completely stop a countdown operation, first pause it (by pressing D), and then press A. This will return the countdown time to its starting value. •The remaining minutes and seconds are counted down on the display until the final minute of the countdown. Only the seconds are displayed during the final minute. Stopwatch The stopwatch measures elapsed time. •The display range of the stopwatch is 59 minutes, 59.99 seconds. •Elapsed time operations are performed internally at units of 1/100-second. When you stop an elapsed time operation, the 1/100-second value will appear on the display. Mode indicator Seconds 1/100 second SecondsMinutes •Only the seconds are displayed during the first 59 seconds of an elapsed time operation. After that, both the minutes and seconds are displayed. •The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. •The stopwatch measurement operation continues even if you exit the Stopwatch Mode. •All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. To measure elapsed time with the stopwatch Elapsed Time Start Stop Re-start Stop Clear Screen when stopwatch elapsed time operation is stopped at 40 minutes, 01.45 seconds Mode indicator Alarm time (Hour : Minutes) Alarm When the daily alarm is turned on, the alarm tone will sound when the alarm time is reached. •All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C. Alarm Operation The alarm tone will sound at the preset time for 10 seconds, regardless of the mode the watch is in. •Alarm operations are performed in accordance with the Timekeeping Mode time. •To stop the alarm tone after it starts to sound, press any button. •In addition to the alarm tone, a Flash Alert operation will be performed whenever the alarm time is reached. The Flash Alert operation will continue for 5 seconds or until you stop it by pressing any button. To set an alarm time 1. In the Alarm Mode, hold down A until the hour setting of the alarm time starts to flash, which indicates the setting screen. •This will turn on the alarm automatically. 2. Press C to move the flashing between the hour and minutes. 3. While a setting is flashing, use D (+) and B (–) to change it. 4. Press A to exit the setting screen. •With the 12-hour format, set the time correctly as a.m. (no indicator) or p.m....
Эта инструкция также подходит к моделям:Часы - 3164 (128.09 kb)