Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
• If there is glue or a similar substance on the disc, remove it completely before using the disc. On storage • Do not expose the disc to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. • Store discs in their cases. Do not store discs either stacked horizontally or standing vertically without their cases. On cleaning • Fingerprints or dust on the disc may cause poor sound reproduction or sound dropout. • Before playing a disc, clean it with a cleaning cloth. Wipe the disc from the center out. • If the disc is still dirty after being wiped with a cleaning cloth, wipe it again with a slightly moistened cloth. Then wipe off the residual moisture with a dry cloth. • Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray intended for vinyl LPs. Note on High-Speed Synchro-Recording Certain CD conditions may cause sound dropout or noise in the recording results, or even create unwanted tracks on the CD-R or CD-RW. If this happens, clean the CD as instructed in “On cleaning” above, and record material to the CD-R or CD-RW using normal speed Synchro-Recording only. Note on CD-R or CD-RW playback When you playback a CD-R or CD-RW recorded by a CD-R or CD-RW recorder, you may not be able to playback depending on the recording conditions (e.g., dirty disc, etc.). Also, you should note that you need to finalize a CD-R or CD-RW before playing back on another system other than the one used to make the recording. (Finalizing is a process to complete the recording.) After finalizing a CD-R, you can play it in any conventional CD player. However, depending on the state of the recording, there may be sound skips during playback. After finalizing a CD-RW, you can play it in a CD-RW compatible player only. Getting Started Unpacking Check that the following items are included: • Audio connecting cords Phono jack . 2 (red/white) y Phono jack . 2 (red/white) (2) • Remote commander (remote) (1) • Size AA (R6) batteries (2) Inserting batteries into the remote You can control the unit using the supplied remote. Insert two size AA (R6) batteries by matching the 3 and # ends on the batteries to the markings inside the compartment. When using the remote, point it at the remote sensor on the unit. Tip With normal use, the batteries should last for about six months. When the remote no longer operates the unit, replace both batteries with new ones. Notes • Do not leave the remote near an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a malfunction. • If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Hooking Up the System This section describes how to hook up the unit to an amplifier. Be sure to turn off the power of each component before making the connections. Connecting the unit to an amplifier Connect the amplifier to the ANALOG IN/ OUT jacks using the audio connecting cords (supplied), making sure to match the color- coded cords to the appropriate jacks on the components: red (R) to red and white (L) to white. Be sure to make connections firmly to prevent hum and noise. Audio connecting cords (supplied) (2) White (L) White (L) Red (R) Red (R) RCD-W50C/W10 Amplifier CD L R INANALOG IN L R OUT l lllll: Signal flow TAPE/MD R INOUT Connecting the unit to a digital component Connect a component such as digital amplifier, CD player, DAT deck, or MD deck through the DIGITAL OPTICAL IN/OUT jacks with the optical digital cord (not supplied). Plug in the cord. Optical digital cord (not supplied) Setting the voltage selector (voltage selector equipped models only) Check that the voltage selector on the rear panel of the unit is set to the local power line voltage. If not, set the selector to the correct position using a screwdriver before connecting the AC power cord to a wall outlet. VOLTAGE SELECTOR 110-120V 220-240V Connecting the AC power cord Connect the AC power cord to a wall outlet. This Unit Can Use the Following Discs The unit can use three types of discs as follows: Audio CD Discs with these logos can be played by both DECK A (the CD player section) and DECK B (the CD-R or CD-RW recording section) of the unit. Audio CD-R Discs with this logo are recordable only one time. When you finalize the disc (page 24), you can play it in either DECK A (the CD player section) or DECK B (the CD-R or CD-RW recording section), or any conventional CD player (you may not be able to play it in some CD players), including home, car, and portable models. (An unfinalized disc can be played only in DECK B.) When you buy a CD-R, please note that you must buy an audio CD-R. A CD-R designed for computer use will not work i...
Эта инструкция также подходит к моделям:CD-проигрыватели - RCD-W50C (492.74 kb)