Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Use the JOG WHEEL (9) to make fine adjustments in pause mode. Use the JOG WHEEL (9) to bend the pitch for precise synchronization in play mode, for scratching, and adjustments to cue and effects parameters. STOP H: The STOP BUTTON (4) will end the playing of the CD as well as clear sampler. TIME: The TIME BUTTON (2) switches the time display between the three available choices listed under DISPLAY. FLY CUE: The FLY CUE (10A) function lets you set cues on the fly with one press of a button. With the unit in the play mode (play/pause LED glows green), press FLY CUE (10A) at the point where you want the cue point to be (the unit will continue to play). The cue point is now memorized. Press the CUE BUTTON (16) to return to the memorized cue point. Push the PLAY/PAUSE BUTTON (17), and the unit will instantly play from the spot selected. CUE: With the unit in the play mode (play/pause LED glows green), and after the cue point has been memorized, pressing the CUE BUTTON (16) will cause the CD player to enter the pause mode (play/pause LED blinks green) at the memorized cue point (the cue LED glows red). Holding down the CUE BUTTON changes the cue function to PREVIEW (allowing you to hear the music play at whatever tempo you adjusted to by holding the cue button down). Releasing the CUE BUTTON returns you to the preset cue point. SEAMLESS LOOP: After a cue point is memorized, pressing the CUE B/ EXIT BUTTON (11) in play mode, repeats the section between the cue point and the point where the CUE B/EXIT BUTTON (11) was pressed. Press the CUE B/EXIT BUTTON (11) again or pause play to exit the repeating play. SINGLE-AUTO CUE/CONTINUOUS: Pressing the SINGLE-AUTO CUE/ CONTINUOUS BUTTON (3) activates the AUTO CUE FUNCTION. The AUTO CUE FUNCTION causes the unit to pause at the beginning of music of the following track and allows you to start play immediately from the start of music without any blank space (which exists at the beginning of every track). Pressing the SINGLE-AUTO CUE/CONTINUOUS BUTTON (3) a second time activates the CONTINUOUS function causing the unit to play continuously (after the last track, the unit will return to the first track of the disc and continue to play). Pressing the SINGLE-AUTO CUE/CONTINUOUS BUTTON (3) a third time deactivates the CONTINUOUS function. ROBO START: Press the ROBO START BUTTON (1) to activate ROBO START function (the button will blink). Use ROBO START in SINGLEAUTO CUE MODE to alternate play between the two sides of the CD player (one track from one side, then one track from the other side). See the Robo Start Instructions section for further instructions. 4%, 12% and 24% BUTTONS: Use the 4%, 12% and 24% BUTTONS (14) to assign the percent the pitch control slide will have. The 4% BUTTON will assign +/-4% to the pitch control slide. The 12% BUTTON will assign +/-12% to the pitch control slide. The 24% BUTTON will assign +/-24% to the pitch control slide. The PITCH (18) must be ON for the 4%, 12% and 24% BUTTONS (14) to work. PITCH: Pushing the PITCH BUTTON (18) activates the PITCH CONTROL (15). The pitch of the CD will change according to the position of the PITCH CONTROL (15). PITCH BEND BUTTONS—-+: Pushing the PITCH BEND BUTTONS (29) will automatically raise the pitch up to +4% or lower the pitch down to -4% from the existing pitch setting. Releasing the buttons will return the pitch to the original pitch setting. You can use this function to match the pitch bend when mixing from one song to another. DIGITAL OUTPUT JACK: Connecting any type of DAT, MD, HARD DRIVE, or other such items which accept digital signals to the BNC OUTPUT CONNECTOR (34) on the rear panel of the transports allows you to record a digital signal. from CD. EFFECT ON/OFF BUTTON: The EFFECT ON/OFF BUTTON (19) turns all effects on and off. EFFECT SELECT BUTTON: The EFFECT SELECT BUTTON (20) allows you to select one of five different effects: The SCRATCH effect makes it possible for the jog wheel to “scratch” the music as it plays. If you move the wheel back and forth the music will stop and play slowly as the wheel is moved, similar to scratching a record. When the wheel stops moving the music will continue. The ZOOM effect changes the delay time by rotating the jog wheel, mixing a short delay with the playback sound. This function allows you to produce the sound of a jet engine (flanger effect) using a single CD player. The FILTER effect allows you to change the cutoff frequency of the playback sound when the jog wheel is rotated. This allows the DJ to extract and play back specific parts from the playback sound. The ECHO effect adds echo to the music. The delay time can be adjusted by turning the jog wheel to the left or right. The REVERSE effect plays your musical selection backwards. When the effect is activated the music will play backwards until it is released. Effect parameters can be adjusted by: 1. Holding down the EFFECT ON/ OFF BUTTON (19) for 3 seconds (the LCD display wil...