Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Two-pin digital audio output terminal for use with a sound or MPEG card supporting digital audio features 2. Four-pin sound output terminal for use with a sound card (refer to the sound card documentation for further details) 3. Master/slave select terminal 4. Forty-pin host IDE interface connector 5. Four-pin power terminal Installing the CD-R/RW Drive To install your CD-R/RW drive in the PC, proceed as follows. 1 Make sure that the PC is powered off and disconnected from any power source. 2 If necessary, attach a horizontal bracket to both sides of the drive. . Use of the brackets depends on your computer model; you can purchase these accessories separately from your computer dealer. 3 Remove the cover from a free expansion slot and install the CD-R/RW drive, as shown in the illustration. If you have no free expansion slot, install the drive in place of the diskette drive. CD-R/RW drive 4 5 Connecting 1. Power cable 2. Master/slave select terminal 3. IDE cable 4. Audio cable 1 Connecting the power cable The 4-pin power cable from the internal power unit of your connected to the power terminal on the rear of the CD-R/RW 2 Installing a jumper on the master/slave select terminal Install the jumper in the correct position on the terminal: MA to use the device in the master mode SL to use the device in the slave mode CS to control the device via a CSEL host interface signal See Step 3 for further details. 3 Connecting the IDE cable Two configurations are possible. The CD-R/RW drive is the only IDE device in addition to the hard disk. IDE port Mother board CD-R/RW (SL) Hard disk (MA) Install the jumper in the SL position (Slave) . Connect the 40-pin flat IDE cable from the IDE port on the mother board, first to the CD-R/RW drive and then to the hard disk. You already have an additional IDE Second IDE cable First IDE cable Mother board CD-R/RW CD-ROM Hard disk Hard disk (MA) (SL) (SL) (MA) Install the jumper in the MA position (Master) . Connect the 40-pin flat IDE cable from a second IDE port on the mother board directly to the CD-R/RW drive or first to another additional IDE drive and then to the CD-R/RW drive. 4 Connecting the audio cable from a sound card Connect the 4-pin audio cable between the sound output terminal on the CD-R/RW drive and the audio input terminal on the sound card. 6 7 Installing Utility To record data on a CD-install the CD record utility. uninstall any existing software 1 Insert the disc supplied with the 2 Follow the instructions displayed on the Refer to the separate utility documentation for further 3 Copy the SHELLEX.DLL file from the root directory on the disc to the DIRECT CD folder. This patch file handles possible errors detected checking the DIRECT CD properties in the Windows Explorer. 4 Store the utility disc in a safe place. Installing the Device Driver No additional device driver is needed for Windows 95/98/NT, as the default Windows device driver is used. You can check that the CD-R/RW drive has been correctly detected by Windows. To do so, proceed as follows. 1 Double-click on the My Computer icon on your desktop. 2 Double-click on the Control Panel folder. 3 Double-click on the System icon. 4 Click on the Device Manager tab. 5 Expand the CD-ROM branch. The SAMSUNG CD-R/RW SW - *** device name is displayed. The SAMSUNG device driver enables discs in the CD-R/RW drive to be read but not recorded in an MS-DOS environment; the driver is located in the D driver folder on the CD record utility disc. Setting Automatic Setup 1 Insert the setup diskette in the where A: is the diskette drive. To do so, type A: after the C:\ prompt and press [Enter] . 2 Type CDSETUP and press [Enter] . 3 Reboot the computer. Manual Setup 1 Make the C:\SAMSUNG directory. 2 Copy the files from the diskette to the C:\SAMSUNG directory. To do so, type COPY A: * . * C:\SAMSUNG after the C:\ prompt and press [Enter] . 3 Edit the CONFIG.SYS file. Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry. LAST DRIVE = Z - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V 4 Edit the AUTOEXEC.BAT file. Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -C :\SAMSUNG\MSCDEX /D:SSCD000 5 Reboot the computer. 8 9 Using the Drive To play audio or video drive, proceed as follows. 1 Push the power button and 2 After booting the computer, open compartment by pressing the Eject button. 3 Insert the disc (CD) with the label on the disc facing upwards and close the disc compartment by pressing the Eject button. The indicator light comes on. 4 Play the disc (CD). Playing Audio CDs Run the CD player supplied with Windows or your sound card. You can the CD by connecting headphones to the appropriate connector. If you have installed the appropriate p...