Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
LCM Monitor 2 LCD, Tuner Pack, IR Remote Controller 3 2. Feature Function, IR Remote 3 2-1 Power 3 2-2 Input Signal Detection 3 2-3 Contrast/Color/Brightness Adjustment 3 2-4 Volume Adjustment 3 2-5 Audio Mute 4 3. Manual Functions 4 3-1 Key Functions 4 3-2 Volume Control 4 3-3 OSD Icons and Functions Description 4 3-4 Video Adjustments 4 Reference table of OSD Functions and Descriptions 5 4. Feature Functions 6 4-1 No Signal Detection 6 4-2 Auto Memory Function 6 4-3 PC VGA Multi-Sync mode 6 5. Tuner Functions: (ACC Function charged only by IR Remote 7 5-1 Power 7 5-2 TV/CATV/AV1/AV2/ Mode Selection 7 5-3 TV/CATV Channel Programming 7 5-4 Input Signal Detection 8 5-5 Channel Selection 8 5-6 Channel Recall 8 5-7 Contrast/Color/Brightness Adjustment 8 5-8 Volume Adjustment 8 5-9 Audio Mute 8 6. Installation of Monitor and Tuner Pack 9 7. Installation Procedure 10 8. Specifications 11 9. Help Page 12 10. Optional Product List 13 11. Notes 14 1. LCM Monitor Front A. IR Eye E. ADJ+ B. Menu F. Power LED C. Select G. Speakers D. ADJ- H. LCD Panel Rear A. VGA Input C. A/V B. DC 12V IN D. Interface Cable to Tuner AUX Page 1 G G H A B C D E F A B C D 2. Feature Function, IR Remote 2-1 Power Pointing the remote towards the IR eye on the LCD, press and hold the POWER On/Off button on the remote controller unit until it turns on the system. Repeat this procedure to turn off system. Power On- The LCD monitor will light up, and the green power light on the front panel will be ON. The OSD (On Screen Display) will show the mode of operation. Power Off- The monitor screen will be dark, the green power light will change to orange. The system will go to stand-by mode. 2-2 Input Signal Detection Tuner system will detect if a signal is received or if a signal is not received in every mode of signal input. If there is no signal, screen will display “No Signal”. Otherwise, the signal will be displayed showing the mode. 2-3 Contrast/Color/Brightness Adjustment If you want to adjust contrast/Color/Brightness, press the appropriate button. The screen will display the one you choose, then use t or s Volume to adjust it within 2.5 seconds. If you take over 2.5 seconds to adjust, the screen display will disappear and the system will reset to t or s Volume. 2-4 Volume Adjustment Use the t or s volume button to increase or decrease the audio volume. You will see the “Volume Bar” on the screen. 2-5 Audio Mute Press the Mute button to disable audio output. The screen will display “Mute” on upper right corner of the monitor. To cancel mute status, just press Mute key again. The “Mute” message on upper right corner will disappear. Page 3 3. Feature Functions by Manual 3-1 Key Functions There are 4 buttons on the monitor which are “Menu”; “Select”; “-“; and “+”. (1) MENU: Pop up & close the OSD (On Screen Display) menu. (2) SELECT: Steps between the function ICONS when OSD menu is on. (3) -: Decreases the adjustment or Pick a selection. (4) +: Increases the adjustment or Pick a selection. NOTE: There are no available functions on the “SELECT” key when the OSD menu is not active. Pressing the “-“/”+” will select volume when OSD menu is not active. See details about the volume control in section 3-2. 3-2 VOLUME ADJUSTMENT BAR Press “-“ or “+” to decrease or increase the volume of the built- in speaker, when the OSD menu is not active. At the same time, the OSD bar will show the adjusted steps. 3-3 OSD ICONS and Function Descriptions Use the “Menu” key on the panel to pop up the OSD. Brightness Contrast Color Hue Volume Pan L/R Pan U/D Size L/R Size U/D Expansion Mute Signal Filter Color System Reset to Default OSD ICONS MENU Use the “Select” key on the panel to step between icons. 3-4 VIDEO ADJUSTMENTS The screen will display the one that you choose, then use the volume s or t to adjust it. If you take longer than 4 seconds to adjust, the menu display will disappear . The system will reset to s or t Volume. Page 4 The Reference table of OSD Functions and Descriptions Mark Function Keyboard Adjust Note Brightness (-) (+) Contrast (-) (+) Color (-) (+) Hue (A/V) / Phase (PC) (-)G R(+) (-) (+) Volume (-) (+) H. Position (-)L R(+) V. Position (-)Up Down(+) H. Size (-)Narrow Wide(+) V. Size (-)Narrow Wide(+) Expansion (-)Off On(+) Mute Speaker (-)Off On(+) Signal Source Select 1. AV/PC - Auto 2. PC/AV - Auto 3. AV 4. PC Auto Detect, AV Priority 1st Auto Detect, PC Priority 1st Only AV Only PC Filter (-)Off On(+) Sharpen/Soften Image System (A/V) 1. NTSC - M / PAL - BGHI 2. PAL 4.43 / NTSC 4.43: 50Hz 3. NTSC 4.43: 60Hz/PAL-N 4. PAL-M / NTSC-N 5. PAL 4.43 / SECAM Color System selection on AV mode Reset- Default (-)Off On(+)Reset to factory setting PWR- On/Off Select + Menu Press Select First Page 5 4. Feature Functions 4-1 No Signal Detection The monitor will detect signal input automatically. If the signal source is OFF or removed, there is a“ “ icon that will appear and blink on the upper right corner of the screen that means “No Signal Input”. The ...