Hold the TX card so that the label "WIRELESS" faces leftward and insert the card into the port. The TX card enables communication between the product and the wireless receiver module. Connect the left and right surround speakers to the wireless receiver module. Plug the power cord of the wireless receiver module in the wall outlet. Turn on the product. The product and wireless receiver module will now communicate with each other and you will hear sound from the Surround speakers. 1. 2. 3. 4. • • 5. 6. 7. TX card Attaching the Toroidal Ferrite Core to the Speaker Cable Open the smaller ferrite core by pulling up the tab. Arrange up the speaker cables that are connected to the FRONT L (+,-) terminal before making 3 loops of them. Attach the ferrite core to the arranged cables and press to close it until you hear a click. Insert the ferrite core as close to the sub woofer as possible. Follow steps 1 through 3 above and insert the ferrite core to each speaker cable that is connected to any of the FRONT R (+,-) and CENTER (+,-) terminals of the sub woofer. Make 3 loops of the speaker cables that are connected to the REAR L and REAR R terminals of the wireless receiver (SWA- 5000) and insert the smaller ferrite core in the same way as step 3 above. 1. 2. 3. • 4. 5. HT-C9950W_ELS_0914.indd 27 2010-09-14 6:54:53 Connections ! CAUTION . . . . . . . . . . . . . Before connecting the speakers, connect the main unit to the subwoofer using the system cable. See page 22. Do not let children play with or near the speakers. They could get hurt if a speaker falls. When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct. Keep the subwoofer speaker out of reach of children so as to prevent children from inserting their hands or alien substances into the duct (hole) of the subwoofer speaker. Do not hang the subwoofer on the wall through the duct (hole). Do not insert any other card except the TX card dedicated to the product. If a different TX card is used, the product may be damaged or the card may not be removed easily. Do not insert the TX card in the reverse direction. Insert the TX card when the product is turned off. Inserting the card when it is turned on may cause a problem. The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and moisture. For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions. If no sound is heard from the wireless surround speakers, switch the mode to DVD 5.1 channel or Dolby Pro Logic II. If no sound is heard from the surround back speakers, switch the mode 7.1channel or Dolby Pro Logic II. In 2-CH mode, no sound will be heard from the wireless surround speakers. . NOTE . . . . . If you place a speaker near your TV set, screen colour may be distorted because of the magnetic field generated by the speaker. If this occurs, place the speaker away from your TV set. Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the product, some sound interruption may be heard due to interference. If you use a device such as a microwave oven, wireless LAN Card or any other device that uses the same frequency (2.4/5.8GHz) near the product, some sound interruption may be heard due to interference. The transmission distance from the product to the wireless receiver module is about 10m, but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal. If the product doesn't make wireless connection, the system needs ID Setting between the product and wireless receiver module. With the product turned off, press the remote control's number buttons "0"."1"."3"."5" and turn on the product. With the wireless receiver module turned on, press "ID SET" button on the back of the wireless receiver module for 5 seconds. 28 English HT-C9950W_ELS_0914.indd 28 2010-09-14 6:54:56 English 29 02 Connections Connecting External Devices/your TV via HDMI HDMI is a standard digital interface for connection to such devices as a TV, projector, DVD player, Blu-ray player, set top box and more. HDMI removes any loss of signal from analogue conversion, enabling you to enjoy video and audio sound quality as it was originally created in the digital source. HDMI OUT : Connecting to a TV with an HDMI Cable Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the subwoofer to the HDMI IN jack on your TV. NOTE Certain HDMI output resolutions may not work, depending on your TV. If an HDMI cable is connected or removed during playback of a CD-DA, MP3 or JPEG fi le, the product will stop playing. After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI) on your...
)
