Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Dell, модель Latitude E6510

Производитель: Dell
Размер: 878.76 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Wake on LAN Allows the computer to turn on by a special LAN signal or from Hibernate state when triggered by a special wireless LAN signal. Wake-up from the Standby state is unaffected by this setting and must be enabled in the operating system. l Disabled — Do not allow the system to power on when it receives a wake-up signal from the LAN or wireless LAN. l LAN Only — Allow the system to be powered on by special LAN signals. The factory default setting is Disabled. ExpressCharge Allows you to enable or disable the ExpressCharge feature. NOTE: ExpressCharge may not be available for all batteries. Charger Behaviour Allows you to enable or disable the battery charger. If disabled, the battery will not lose power when the system is connected to an AC adapter but it will not charge either. Default setting: Enabled POST Behaviour Option Description Adapter Warnings Allows you to enable or disable the BIOS warning messages when you use certain power adapters. The BIOS displays these messages if you attempt to use a power adapter that has too little capacity for your configuration. The factory default setting is Enabled. Keypad (Embedded) Allows you to select one of two methods to enable the keypad that is embedded in the internal keyboard. l Fn Key Only — The keypad is only enabled when you hold down the key. l By Num Lk — The keypad is enabled when (1) the Num Lock LED is on and (2) no external keyboard is attached. Note that the system might not notice immediately when an external keyboard is detached. NOTE: When Setup is running, this field has no effect—Setup works in the Fn Key Only mode. Default setting: Fn Key Only. Mouse/Touchpad Determines how the system handles mouse and the touchpad input. Default setting: Touchpad/PS-2 Mouse. Numlock LED Allows you to enable or disable the Num Lock LED when the computer boots. Default setting: Enabled. USB Emulation Defines how the BIOS handles the USB devices. USB emulation is always enabled during POST. The factory default setting is Enabled. Fn Key Emulation Allows you to use the key on an external PS/2 keyboard the same way you use the key on the computer's internal keyboard. NOTE: USB keyboards cannot emulate the key if you are running an ACPI operating system such as Microsoft® Windows® XP. USB keyboards will only emulate the key in non-ACPI mode (e.g., when you are running a DOS). Default setting: Enabled. Fast Boot Allows you to enable or disable the Fast Boot feature. The following options are available: l Minimal — Boot quickly unless the BIOS has been updated, memory changed, or the previous POST did not complete. l Thorough — Do not skip any steps in the boot process. l Auto — Allow the operating system to control this setting (this works only when the operating system supports Simple Boot Flag). Default setting: Minimal Intel Fast Call for Help Used in conjunction with iAMT 4.0. Allows you to initiate contact with a management console while residing outside of the corporate infrastructure (i.e. remote location, behind a firewall or NAT, etc.) Use the check box to enable / disable this feature. Default setting: Disabled Virtualization Support Option Description Virtualization Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel Virtualization Technology. Default setting: Enabled. VT for Direct I/O Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel Virtualization Technology for Direct I/O. Default setting: Disabled. Trusted Execution Specifies whether a Measured Virtual Machine Monitor(MVMM) can utilize the additional hardware capabilities provided by Intel Trusted Execution Technology. Default setting: Disabled. Wireless Option Description Wireless Switch Allows you to choose the wireless devices that can be controlled by the wireless switch. Wireless Devices Enable Allows you to enable or disable the following internal wireless devices: WWAN, WLAN, and Bluetooth. Maintenance Option Description Service Tag Displays your computer's Service Tag. If for some reason the Service Tag was not already set, you would be able to use this field to set it. If a Service Tag has not been set for this computer, the computer will automatically bring up this screen when you enter the BIOS. You will be prompted to enter the Service Tag. Asset Tag Allows you to create a system Asset Tag. The field can only be updated if the Asset Tag is not already set. System Logs Option Description BIOS Events Allows you to view and clear BIOS POST events. It includes the date and time of the event as well as the LED code. DellDiag Events Allows you to view the diagnostic results from Dell Diagnostics and PSA. It includes the time and date, the diagnostic and version which was run and the resulting code. Back to Contents Page Thermal Events Allows you to view and clear thermal events. It includes the date and time as well as the...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории