Войти:
Оценок - 13, средний балл: 4 ( )

Инструкция по эксплуатации Linksys, модель PAP2T-NA

Производитель: Linksys
Размер: 346.17 kb
Название файла: Linksys_PAP2_Devices_Admin_Guide.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Disclaimer The content of this manual is subject to change without notice and should not be construed as a commitment by the manufacturer, distributor, or service provider. This manual is furnished for informational use only and the manufacturer, distributor, or service provider assumes no responsibility for any errors or inaccuracies that may appear herein. Linksys PAP2 Devices Administrator’s Guide Table of Contents 1 WELCOME ............................................................... 2 OVERVIEW ............................................................................ 2 CONFIGURING THE PAP2 DEVICE WITH NET2PHONE’S PROVISIONING SERVER ......................................................... 3 REMOVING VOICELINE SERVICE ............................................ 9 i Linksys PAP2 Devices Administrator’s Guide 1 Welcome Overview Congratulations on purchasing your Linksys PAP2 telephone adapter! The Linksys PAP2 device is a voice over Internet protocol telephone adapter. It is based on the SIP (Session Initiation Protocol), which is by far the most widely used protocol by Internet telephone service providers (ITSP). The PAP2 device can be directly connected to a broadband Internet connection to access the services provided by the ITSPs. Prior to deploying the Linksys PAP2 device to your customer, it must be configured to point to Net2Phone’s provisioning server where it downloads its account information. This manual will guide you through the process of provisioning each Linksys PAP2 device via the Linksys Web Interface. Note that the adapter will not function unless Net2Phone’s provisioning server is configured on the device. Once an account has been created for the device in the Partner Resource Center (PRC), it can be rebooted and will download its unique account information. At this point the adapter is ready to make and receive calls. 2 Linksys PAP2 Devices Administrator’s Guide Configuring the PAP2 device with Net2Phone’s Provisioning Server NOTE: The provisioning process can be completed prior to provisioning the device in the Partner Resource Center. TO PROVISION THE LINKSYS PAP2 DEVICE: 1. Determine which PAP2 device you are using. By turning the device over you can view the model number of the device type you are configuring – PAP2-NA, PAP2T-NA, or PAP2T-R. Refer to the following images to identify your PAP2 device: PAP2-NA 3 Linksys PAP2 Devices Administrator’s Guide PAP2T-NA PAP2T-R 4 Linksys PAP2 Devices Administrator’s Guide STOP!: Be sure to identify the correct device prior to provisioning. The service will not function if the incorrect provisioning string is used. 2. Connect the Linksys PAP2 to your network by connecting one end of a network cable to the Ethernet port and the other end to your broadband router. Once the adapter is connected to the network 3. If you have the: • PAP2-NA or PAP2T-NA, continue with the next step. • PAP2T-R, proceed to Step 13. 4. Using a standard telephone wire (RJ-11), connect a telephone to the PHONE 1 port on the back of your PAP device. 5. Dial **** (four stars), followed by 110#. The IP address is announced. 6. Write down the IP address. 7. From a PC on the same network as the PAP device, login to the PAP device Web Interface by opening your web browser and entering address into the address field and pressing . 8. Click the Admin Login link. 5 Linksys PAP2 Devices Administrator’s Guide 9. Enter your Login and Password. 10. Click the switch to advanced view link at the top of the page. 11. Select the Provisioning tab at the top of the page. 12. In the Profile Rule field enter the string assigned to your particular PAP device model. PAP2-NA: MA&ver=$SWVER 6 Linksys PAP2 Devices Administrator’s Guide PAP2T: &ver=$SWVER IMPORTANT: The string is case-sensitive and must be entered exactly as it appears. Failure to do so will render the adapter non-functional. 7 Linksys PAP2 Devices Administrator’s Guide IMPORTANT: Be certain that you are using the correct string for your particular PAP device model number. Failure to do so will render the device non-functional. 13. Click the Submit all changes button at the bottom of the page 14. Reboot the PAP device by disconnecting the A/C power cord from the device, waiting 5 seconds, and re-connecting it. 15. After the adapter reboots, if an account has already been created for the device in PRC (Partner Resource Center), verify that the configuration was successful by noting that the blue PHONE 1/2 LED is lit. If an account has not yet been created for the device in PRC, the PHONE 1/2 LED will remain unlit. Once an account has been created in PRC for the device, reboot the device. The LEDs will then turn blue. NOTE: After the provisioning is complete, the Admin pages on the PAP2 device web interface will not be accessible. The user can only access the Info, System, and User tabs from the PAP2 device’s We...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории