Войти:
Скачали: 0   Размер: 133 kb   Производитель: Makita  
Категория: Бензо и электропилы

Скачали: 2   Размер: 1 mb   Производитель: Makita  
Категория: Бензо и электропилы
@name

17. Make the lower horizontal notching cut first. This will help to avoid pinching of either the saw chain or the guide bar when the second notch is being made. Felling back cut Make the felling back cut at least 2 inches (50.8mm) higher than the horizontal notch- ing cut as shown in Fig. 17. Keep the fell- ing back cut parallel to the horizontal notching cut. Make the felling back cut so enough wood is left to act as a hinge. The hinge wood keeps the tree from twisting .and falling in the wrong

Скачали: 10   Размер: 1 mb   Производитель: Makita  
Категория: Бензо и электропилы
@name

Keep the cord away from the cut- ting area and to position cord so that it will not be caught on branches, and the like, during cutting. Use the table below to determine the proper wire size re- quired in the extension cord. Ampere rating (on nameplate) 0 -5.0 5.1 -10.0 10.1 -13.0 13.1 -15.0 Ext. Cord Length Wire Size (American Wire Gauge) 25 Ft. 18 18 16 14 50 Ft. 18 16 16 14 75 Ft. 18 16 14 14 100 Ft. 16 14 12 12 125 Ft. 16 12 12 12 150 Ft. 16 12 12 - ~ ~ ~ Contact Makita Authorized or Factory

Скачали: 16   Размер: 1 mb   Производитель: Makita  
Категория: Бензо и электропилы
@name

Attach the hook about 100-200 mm (4"- 8") from the extension cord connector. This will help prevent unintentional dis- connection. Extension cord Fig. 11 Cutting operation Turn the tool on and allow the chain to reach full speed before it contacts the wood. Be sure the chain is adequately lubricated. Use the spike as a pivot point and ease the tool into the wood, rocking it in gently. Do not force the guide bar in, as this may cause overload -and overheating. Fig. 1: Instant chain brake This too

Скачали: 17   Размер: 2 mb   Производитель: Makita  
Категория: Бензо и электропилы

Скачали: 10   Размер: 362 kb   Производитель: Makita  
Категория: Бензо и электропилы
@name

-With the engine running at moderate speed, press the hand guard (C/1) in the direction of the arrow with the back of your hand until the chain brake engages. The chain should stop immediately. -Immediately release the throttle and release the chain brake. IMPORTANT: If the chain does not stop immediately when you test the chain brake, do NOT use the saw! Take the saw to a MAKITA service center. Adjusting the carburetor CAUTION: Optimum perfornance can only be achieved if the carburetor is adjus

Скачали: 2   Размер: 5 mb   Производитель: Makita  
Категория: Бензо и электропилы
@name@name

The sprocket is located underneath the clutch drum (8). CAUTION: Worn out sprockets (9) may damage the new chain and must therefore be replaced. Do not attempt to replace the sprocket yourself. Sprocket replacement requires special training and tools and must be done at a MAKITA service centre. 7 8 9 Replacing the suction head The felt filter (10) of the suction head can become clogged. It is recommended to replace the suction head once every three months in order to ensure unimpeded fuel flow t

Скачали: 164   Размер: 6 mb   Производитель: Makita  
Категория: Бензо и электропилы
@name@name

Always follow safety precautions in the Owner’s and Safety Manual. Improper use can cause serious injury! Preserve this Manual carefully! ATTENTION! Suivez toujours les conseils de securite du present manuel d’emploi et de securite. Une utilisation incorrecte de la tronconneuse peut entrainer des blessures graves! Conservez avec soin ce manuel. Lisez et comprenez ce manuel. WARNING ! WARNING ! Before operating a chain saw or other MAKITA products it is important that you read, fully understand a

Скачали: 11   Размер: 6 mb   Производитель: Makita  
Категория: Бензо и электропилы
@name@name

Additional safety precautions The following additional safety precautions should be observed by all users of chain saws: 1. Do not operate a chain saw when you are fatigued. 2. Use safety footwear; snug-fitting clothing; protective gloves; and eye, hearing, and head protection devices. 3. Use caution when handling fuel. Move the chain saw at least 10 feet (3 m) from the fueling point before starting the engine. 4. Do not allow other persons to be near the chain saw when starting or cutting with

Скачали: 49   Размер: 6 mb   Производитель: Makita  
Категория: Бензо и электропилы
@name@name

The chain saw DCS 340, DCS 341, DCS 400, DCS 401 has been approved with following guide bar and chain combinations: Guide bar 3/8" Saw chain 3/8" length Part no. Part no. 12" (30 cm) 442 030 661 528 092 646 14" (35 cm) 442 035 661 528 092 652 16" (40 cm) 442 040 661 528 092 656 "There may be other replacement bar and chain combinations available that also reduces the risk of injury from kickback". WARNING Do not use other replacement bars and chains unless they have been designated as meeting th





Категории