Оценок - 3, средний балл: 3.7 ( )

Производитель: Desa Размер: 3.81 mb Название файла: Язык инструкции:

Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see Replacement Parts and Accessories, page 16. Flat FileDepth Gauge SlotDepth Gauge ToolDepth Gauge Figure 22 - Depth Gauge Tool On Chain Front Corner .025" .635 mm Figure 23 -Round Off Front Corner Of Depth Gauge ENGLISH 107705 15 STORAGE If storing saw for more than 30 days, follow steps below. 1. Drain oil tank after each use. 2. Remove and clean guide bar and chain. Clean guide bar and chain by soaking in petroleum based solvent or mild soap and water mixture. 3. Dry guide bar and chain. 4. Place chain in container filled with oil. This will prevent rust. 5. Wipe a thin coating of oil over surface of guide bar. 6. Wipeoffoutsideofsawbody.Dothiswithsoftcloth dampened with a mild soap and water mixture. 7. Store chain saw • in a high or locked place, out of children’s reach • in a dry place • in a carrying case or with scabbard over guide bar TECHNICAL SERVICE You may have further questions about assembling, operating, or maintaining this product. If so, you can visit our Technical Service web site at desatech.com or contact our Technical Service Department at 1-800-858-8501 (English Only). You may also write to: DESA Specialty Products™ ATTN: Technical Service Specialty Products P.O. Box 90004 Bowling Green, KY 42102-9004 When contacting DESA Specialty Products™, have ready • Your Name • Your Address • Your Phone Number • Model Number of Product • Date of Purchase (Include copy of receipt for written requests). REPLACEMENT PARTS AND ACCESSORIES WARNING:Useonlyreplacementparts andaccessoriesdescribedinthismanual. Use of other parts or accessories could damage saw or injure operator. For original replacement parts and accessories, contact your nearest Authorized Dealer or Authorized Service Center for this product. If they can not supply the part or accessory, contact your nearest Parts Central listed on page 59. Each Authorized Dealer, Authorized Service Center, and Parts Central is independently owned and operated. See pages 60 through 63 for an Illustrated Parts List. If you need additional referral information, contact our Technical Service Department (see Technical Service). In Canada call 1-800-561-3372 for parts information. REPAIR SERVICE Note: Only use original replacement parts. This will protect your warranty coverage for parts replaced under warranty. Each Authorized Service Center is independently owned and operated. WARRANTY SERVICE If product requires warranty service, return it to nearest Authorized Service Center. You must show proof of purchase. If faulty materials or workmanship caused damage, we will repair or replace product without charge. Note: Normal wear, misuse, abuse, neglect, or accidental damage is not covered under warranty. NON-WARRANTY SERVICE If product requires service, return it to nearest Authorized Service Center. Repairs will be billed to you at regular repair list prices. For additional Service Center or warranty information, call 1-800-858-8501 or visit our Technical Service web site at 107705 16 TROUBLESHOOTING WARNING: Unplug chain saw from Note: For additional help, visit DESA Specialty powersourcebeforeservicing.Severeinjury Products’™ technical service web site at or death could occur from electrical shock desatech.com. or body contact with moving chain. OBSERVED FAULT POSSIBLE CAUSE REMEDY Saw runs, but does not cut Saw does not cut unless heavily forced. Cutting produces only sawdust with few large chips Chain assembled backwards guide bar Chain is dull on See Assembly, pages 7 and 8 See Sharpening Saw Chain, pages 14 and 15 Saw runs slow. Saw stalls easily Low power supply voltage Extension cord wire size too small. See Extension Cords, page 10 Motor of saw does not run when you 1. Switch lockout not pushed for-1. Push switch lockout forward squeeze trigger ward in to release trigger before squeezing trigger 2. Extension cord connections loose 2. Check cord connections 3. Open line fuse or circuit breaker 3. Check line fuse or circuit breaker 4. Worn out motor brushes 4. See authorized service center 5. Open wiring circuit on saw 5. See authorized service center Motor of saw runs, but chain does Gear train failure See authorized service center not move Chain does not get oil All Models 1. Clogged oil slot in guide bar 1. Remove guide bar and clean oil slot 2. Oil is too thick 2. Use correct weight of oil. See Filling Oil Tank, page 9 Models with Automatic Oiler 1. Vent in oil cap clogged 1. Remove cap and clean vent hole 2. Filter in oil reserVoir clogged 2. Remove filter in oil reserVoir and clean 3. Pump damaged, do not use saw 3. See authorized service center Chain comes off guide bar 1. Chain is loose 1. Tightenchain.SeeSaw Chain Tension Adjustment, pages 8 and 9 2. Guide bar and chain not as-2. See Assem...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: