Войти:
Оценок - 3, средний балл: 4 ( )

Инструкция по эксплуатации McCulloch, модель Electramac 416

Производитель: McCulloch
Размер: 2.11 mb
Название файла:
Язык инструкции:itenpt
Перейти к скачиванию



Фрагмент инструкции


The depth of the notch should be equal to about 1/4 of the diameter of the ENGLISH - 3 tree and the angle of the upper and lower cuts should be at least 45°. Main cut The main cut is made on the opposite side from the directional cut and must be perfectly horizontal, and at a height about 3 cm above the base of the directional cut (see illustration) Finish the cut at least 1/10 of the tree diameter from the directional notch. This is called the breakage line and serves to control the direction of fall of the tree because the tree will now start to fall. This can be facilitated using a crowbar on the main cut. Caution! If the breakage line is too small or is cut diagonally it will no longer be possible to control the direction of fall of the tree. F. Sharpening the bar and chain, and maintenance of the bar • Important: unplug the chainsaw before performing any cleaning and maintenance of the tool. • Always wear approved work gloves • Fig. B6 make sure the chain is tight enough to prevent it from moving during sharpening • Fig. F1 pull the brake lever forward to block the chain on the bar • The correct diameter of the file is 1/10 or more than the height of the cutting tooth. • FIG. F2 Round file for sharpening 4 mm chain • FIG. F3 File at a horizontal angle of 35° to the bar from the inside of the tooth toward the outside. First file all the teeth on one side then turn the chainsaw and file the teeth on the other side • File in such a way that all the teeth are the same length. • When only 3 mm (1/8”) of the length of the cutting teeth remains, replace the chain. • FIG F4 file perpendicular to the bar plane (90°) • FIG F5 About every 5 sharpenings, check the cutting height against the cutting depth limiter (H). To reduce the height of the limiter use a caliber. • FIG F6 Every 3 hours of work remove the bar and clean the groove, make sure the oil outlet hole is not obstructed by chips and remove all sawdust deposits from the tool. Important: reverse the direction of installation of the bar every time you clean it so as to obtain uniform wear • FIG F7 Check frequently that the ventilation slots on the motor are free and the grating is clean. Electric safety Voltage Plugs and extension cables Make sure the voltage rating of your mains Use only approved insulated outlets, cables and complies with the rating of the chainsaw as shown plugs in PVC, comply strictly with the safety on the plate on the motor casing. regulations in effect in your country. The tool has to be plugged into a power socket and not a light socket. Current Your tool works only with AC power. Disposal of obsolete products When you decide to replace the product, or no dispose of it in a way that is safe for the longer need it, think of the environment. Your local environment. distributor will take your old product back and ENGLISH - 4 Troubleshooting table Motor does not start Motor turns with difficulty or loses power Chainsaw starts but does not cut properly Motor turns improperly ...

Эта инструкция также подходит к моделям:
Бензо и электропилы - Electramac 414 (2.11 mb)
Бензо и электропилы - ElectraMac 95390054000 (2.11 mb)
Бензо и электропилы - ElectraMac 95390041500 (2.11 mb)
Бензо и электропилы - Electramac 95390041600 (2.11 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории