Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Keep flammable materials away, and do not place anything on the engine while it is running. Text surrounded by a box is additional information specifically for LPG model engines ONLY. Disregard this information if your engine is operating on gasoline. POM52355F IPC 3,000.2004.01 HELPFUL TIPS & SUGGESTIONS. . . . . . . . . . . . . . .7 Storing Your Engine . . . . . . . . .7 Adding A Gasoline Stabilizer To Extend Fuel Storage Life . . . . . . . . . . . . . . . .7 Draing The Fuel Tank And Carburetor . . . . . . . . . . . . . . . . .8 Transporting . . . . . . . . . . . . . . .8 TAKING CARE OF UNEXPECTED PROBLEMS. . . . . . . . . . . . . . . . . .8 TECHNICAL & CONSUMER INFORMATION . . . . . . . . . . . . . . .8 Technical Information . . . . . . . 8 Serial Number Location . . . . . . 8 High Altitude Operation . . . . . . 9 Oxygenated Fuels. . . . . . . . . . .9 Emission Control System Information. . . . . . . . . . . . . . . . .9 Air Index. . . . . . . . . . . . . . . . . .10 Specifications . . . . . . . . . . . . .10 Tuneup Specifications . . . . . . 10 Consumer Information . . . . . . 10 Honda Publications. . . . . . . . . 10 Wiring Diagram . . . . . . . . . . . .10 Distributor’s Limited Warranty. . . . . . . . . . . . . . . . . .11 Emission Control System Warranty. . . . . . . . . . . . . . . . . .11 Distributor/Dealer Locator Information. . . . . . . . . . . . . . . .12 Customer Service Information. . . . . . . . . . . . . . . .12 © 2000 - 2004 American Honda Motor Co., Inc.—All Rights Reserved 1 COMPONENT & CONTROL LOCATION COMPONENT & CONTROL LOCATION RECOIL (LPG MODELS) THROTTLE GRIP FUEL TANK CAP AIR FILTER CONTROL MUFFLER SPARK PLUG CAP OIL FILLER CAP/ DIPSTICK OIL FILTER STARTER SOLENOID THROTTLE CABLE CONNECTION THROTTLE The throttle lever is provided with CABLE5 mm CABLE HOLDERTHROTTLE LEVERCHOKE ARM PULL holes for attaching a solid wire throttle cable. SCREW 1. Remove the 5 mm screw and the cable holder. Hook the solid wire cable end into the throttle lever as shown. 2. Move the throttle cable control (located on equipment) into the FAST (or HIGH) throttle position. 3. Move the throttle lever by pulling the throttle cable until the throttle lever just contacts the choke arm. Install the cable holder securing the throttle cable and tighten it securely. CHOKE ROD LEVERFASTCHOKE ADJUSTING SCREWCHOKE THROTTLE 4. Move the throttle control (located on equipment) to move the throttle lever to the CHOKE CHOKE position. Verify the engine choke rod moves the carburetor choke fully closed. Adjust the adjusting screw until it just contacts the choke arm. 5. Start the engine and move the throttle lever to the FAST (or HIGH) position. Using a tachometer, check the engine speed. Loosen the cable holder bolt and move the throttle cable to obtain the top no load engine speed specified by the equipment manufacturer. Tighten the cable holder bolt securely. 6. Move the throttle cable control lever to the STOP position and confirm that the engine stops. LPG CONNECTIONS This engine is certified to comply with U.S. EPA and California ARB emission regulations using the Impco Beam regulator specified in the installation instructions (see below). Honda used this regulator and other specific parts and adjustments to demonstrate compliance with the emission regulations. Adjustable fuel system parts must have U.S. EPA and California ARB approved tamper resistant features to limit the available adjustment after the fuel system is correctly installed. If an equipment manufacturer did not install your engine in a product you will need the installation instructions for the Honda certified system (see below). If you choose not to use the Honda fuel system you must use a system that has been certified by the fuel system manufacturer to be used on this Honda engine. Or if you use a fuel system that is not already certified you must have certification test data satisfactory to the U.S. EPA or the California ARB. The test data must prove that the system will meet the emission standard both when the engine is new and at the end of its emission durability period (250 hours). To obtain a copy of the installation instructions for this engine, contact an independent Honda engine distributor, or our Customer Service Department (page 12). BATTERY CONNECTIONS Use a 12 volt battery with an ampere-hour rating of at least 18 AH. Coat the terminals and cable ends with grease. Be careful not to connect the battery in reverse polarity, as this will short circuit the battery charging system. . WARNING A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery. 1. Connect the battery positive (+) cable to the starter solenoid terminal as shown. 2. Connect the battery negative (-) cable to an engine mounting bolt, frame bolt, or other good engine ground connection. 3. Connect the battery positive (+) cable to the battery positive (+) termina...
Эта инструкция также подходит к моделям:Бензо и электропилы - GXV390 (525.84 kb)