Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Remove muffler (B) and muffler gasket (C ). 5. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. iMPOrTanT Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder. 6. Inspect muffler gasket, and replace if damaged. 7. Install muffler gasket and muffler. 8. Tighten muffler mounting bolts (or nuts) to 60-95 in • lbf (70-110 kgf • cm). 9. Install muffler support bracket (A). 10. Install guide bar and saw chain. See "Guide Bar and Saw Chain Installation/Removal." 11. Install spark plug lead and air cleaner cover. 12. Start engine, and warm to operating temperature. Stop engine. 13. Remove air cleaner cover and remove spark plug lead. 14. Remove guide bar and saw chain. See "Guide Bar and Saw Chain Installation/Removal." 15. Remove muffler support bracket. 16. Re-tighten mounting bolts (or nuts) to specifications. 17. Install muffler support bracket. 18. Install guide bar and saw chain. See "Guide Bar and Saw Chain Installation/Removal." 19. Install spark plug lead and air cleaner cover. 29 CS-450SETTING THE SAW CHAIN Sharpen lower edge Drive link Tie strap Right hand cutter Preset tie strap Left hand cutter Guard link Top plate Side plate Depth guage Important points for proper maintenance of saw chain: • Keep the cutters sharp at all times. • Keep the left and the right cutters properly aligned. -Note that blunt or irregular cutters will result in poor cutting performance, increased vibration of chains and premature breakage of the saw chain. • Drive link serves to remove sawdust from the groove of the guide bar. Keep the lower edge of the drive link sharp where indicated. SETTING SAW CHAIN Proper filing tools for setting saw chain are avail- able from your Echo dealer. • For setting saw chain, round file (33SL : 4.5 mm dia. or 20BPX, 95VP : 3/16 in.) and flat file are used. • To keep correct position and correct angle, use the file holder (Sure Sharp®). Hold the file tipped 10° upward 10° Keep this angle Push file as shown 33SL : 25° 20BPX, 95VP : 30° CS-450SETTING THE SAW CHAIN Sharpen lower edge Drive link Tie strap Right hand cutter Preset tie strap Left hand cutter Guard link Top plate Side plate Depth guage Important points for proper maintenance of saw chain: • Keep the cutters sharp at all times. • Keep the left and the right cutters properly aligned. -Note that blunt or irregular cutters will result in poor cutting performance, increased vibration of chains and premature breakage of the saw chain. • Drive link serves to remove sawdust from the groove of the guide bar. Keep the lower edge of the drive link sharp where indicated. SETTING SAW CHAIN Proper filing tools for setting saw chain are avail- able from your Echo dealer. • For setting saw chain, round file (33SL : 4.5 mm dia. or 20BPX, 95VP : 3/16 in.) and flat file are used. • To keep correct position and correct angle, use the file holder (Sure Sharp®). Hold the file tipped 10° upward 10° Keep this angle Push file as shown 33SL : 25° 20BPX, 95VP : 30° 1/5 One fifth of file diameter remains above cutter edge Remove until flat with tool Depth gauge tool Round off the edge Top plate filing angle 33SL : 25° 20BPX, 95VP : 30° Parallel 0.64 mm (0.025 in.) Top plate cutting angle Depth gauge 20BPX :55° 33SL, 95VP :60° • Place the depth gauge tool firmly on guide bar so that depth gauge protrudes. Then file top of depth gauge with the flat file until flat with top of the depth gauge tool. -Be sure to round off the front edge of the depth gauge. Properly filed cutters are shown in illustration. When setting of the chain is finished, soak it in oil and wash away filings completely before using. -When chain has been filed on the bar, supply sufficient oil to it, rotate the chain slowly to wash away the filings before using again. -If the chain saw is operated with filings clogged in the groove, the saw chain and the guide bar will be damaged prematurely. -If the saw chain becomes soiled with resin, for instance, clean it with kerosene and soak in it oil. NOTE These angles are referred to as Oregon 20BPX, 33SL, or 95VP. To sharpen other follow chain manufacturer’s instruction. 30 TROUBLESHOOTING EnginE PrOBLEM TrOUBLESHOOTing CHarT Problem Check Status Cause remedy Engine cranks starts hard/ t'doesn start Fuel at carburetor No fuel at carburetor Fuel strainer clogged Fuel ilne clogged Carburetor Clean or replace Clean or replace See your Echo dealer Fuel at cyilnder No fuel at cyilnder Carburetor See your Echo dealer Muffler wet with fuel Fuel Mixture too rich Open choke Clean/replace air filter Adjust carburetor See your Echo dealer Spark at end of plug wire No spark Stop switch off Electrical problem Interlock switch Turn switch to ON See your Echo dealer See your Echo dealer Spark at plug No spark Spark gap incorrect Covered with carbon Fouled with fuel Plug defective Adjust to .65mm (0.026 in.) ...
Эта инструкция также подходит к моделям:Бензо и электропилы - CHAIN SAW CS-450 (1.27 mb)