Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION: PROTEGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITE AFIN D'EVITER TOUT RISQUE D'INCENDIE OU D'ELECTROCUTION. POUR REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE. FXT120 Guitar Amp with DSP & Channel Tracking FXT120 Guitar Amp with DSP & Channel Tracking The Digital Signal Processor: The FXT120’s Digital Signal Processor provides 16 exciting digital effects. Use the DSP Selector control to choose the desired effect, then use the DSP Level control to mix in the desired amount of effect. The effects are described below: FLNG 1 slow deep flange + reverb FLNG 2 flange + reverb + delay CHO 1 CHO 2 chorus + reverb + delay RTRY simulated rotary speaker effect OCTV DOWN adds a signal one octave lower than input T-WAH touch sensitive wah-wah effect I-WAH inverse wah-wah effect DOUBLER simulated second track, slightly out of sync REV (1) small room reverb REV (2) medium room reverb REV (3) large room reverb REV (4) concert hall reverb DLY (1) short slapback + small room reverb DLY (2) medium delay + plate reverb DLY (3) long delay + large room reverb slow tremolo chorus + reverb Channel Tracking: The FXT120 gives you the power of Channel Tracking! Once you select a DSP setting for each channel, Channel Tracking recalls those DSP setting automatically – without changing the DSP controls! For example: • Select the Clean channel. Set the DSP Selector to “FLNG 1” (slow flange + reverb) • Select the Overdrive channel, Gain 1. Set the DSP Selector to “CHO 1” (slow chorus + reverb) (the setting for the Clean channel is now saved to memory) • Select the Overdrive channel, Gain 2. Set the DSP Selector to “T-WAH” (touch wah-wah) (the setting for the Overdrive channel, Gain 1 is now saved to memory) • Reselect the Clean channel (the setting for the Overdrive channel, Gain 2 is now saved to memory) Now when you go back to the Clean channel, even though the DSP Selector was last set to “T-WAH,” Channel Tracking automatically recalls the last setting for the Clean channel – in this example, “FLNG 1.” Change to the Overdrive channel, Gain 1, and “CHO 1” is recalled. Change to the Overdrive channel, Gain 2, and “T-WAH” is recalled. That’s the power of Channel Tracking! (Note: Even when the power is turned off, Channel Tracking still retains the settings – until you change them!) 3 FXT120 Guitar Amp with DSP & Channel Tracking FXT120 Guitar Amp with DSP & Channel Tracking The Front Panel: 1 2 4 6 7 8 1010 1111 1212 1313 1414 1515953 1: INPUT: Use this jack to connect your guitar to the amplifier by means of a shielded instrument cable. OVERDRIVE CHANNEL: A high gain channel giving you sounds from a slight edge to serious overdrive. 2: GAIN 1: Use this control to adjust the amount of light distortion for the Overdrive channel. Gain 1 produces less intense distortion than Gain 2 (#3) and is active when the Gain Select switch (#5) is in the out position. 3: GAIN 2: Use this control to adjust the amount of heavy distortion for the Overdrive channel. Gain 2 produces more intense distortion than Gain 1 (#2) and is active when the Gain switch (#5) is depressed. 4: SHAPE: Use this control to “dial in” the tone for the Overdrive channel when Gain 2 is selected. Rotating the control counterclockwise enhances the mid frequencies, while rotating the control clockwise enhances the low and high frequencies. This control is only active when Gain 2 is selected. 5: GAIN SELECT: Use this switch to select which Gain control is active for the Overdrive channel. With the switch in the out position, Gain 1 is selected. When the switch is depressed, Gain 2 is selected. When a footswitch is connected to the Channel / Gain Select Footswitch jack (#21), this switch is inactive and the Gain Select function is controlled by the footswitch (see #21). 6: LOW: Use this control to adjust the low frequency level of the Overdrive channel. 7: HIGH: Use this control to adjust the high frequency level of the Overdrive channel. 8: LEVEL: Use this control to adjust the output level of the Overdrive channel. 9: CHANNEL SELECT: Use this switch to select either channel. With the switch in the out position, the Clean channel is selected. When the switch is depressed, the Overdrive channel is selected. The adjacent LEDs illuminate to indicate which channel is active. When a footswitch is connected to the Channel / Gain Select Footswitch jack (#21), this switch is inactive and the Channel Select function is controlled by the footswitch (see #21). CLEAN CHANNEL: A normal gain channel designed to give you crystal clear sounds to medium distortion. 10: VOL: Use this control to adjust the output level of the Clean channel. 11: LOW: Use this control to adjust the low frequency level of the Clean channel. 12: MID: Use this control to adjust the midrange frequency level of the Clean channel. 13: HIGH: Use this c...