Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
50-250Hz Low Pass (Model DX500.1 / 1000.1 /2000.1). G. Remote Level Control: (Model DX500.1 / 1000.1 /2000.1 ) Attenuates Gain set on the amplifier by up to -12dB. H. Speaker Connections: Follow correct polarity, and do not Ground any speaker wires. Do not connect any speaker wires together. I. Pass Thru Outputs: The Pass-Thru provides a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the rear amplifier location. J. Subsonic Control: (Model DX500.1 / 1000.1 / 2000.1) A variable 15-40Hzhigh pass filter designed to prevent frequencies below the audio range from being applied to the subwoofer from the amplifier. Improving subwoofer performance and power handling. K. Master/Slave Switch: (Model DX500.1 / 1000.1 /2000.1) Used to set the amplifier to master or slave when strapping. L. SLV IN (slave): (Model DX500.1 / 1000.1 / 2000.1) When strapping, this is the slaved amplifier input from the master amplifier M. MAS OUT (master): (Model DX500.1 / 1000.1 / 2000.1) When strapping, this is the master amplifier output to the slave amplifier Installation hi installation considerations The following is a list of tools needed for installation: Volt/Ohm Meter Wire strippers Wire crimpers Wire cutters # 2 Phillips screwdriver Hand held drill w/assorted bits 1/8" diameter heatshrink tubing Assorted connectors Adequate Length - Power Wire Adequate Length - Remote Turn-on Wire Adequate Length - Grounding Wire This section focuses on some of the vehicle considerations for installing.your new Amplifier. Pre-planning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments. A CAUTION: If you feel unsure about installing this system yourself, have it installed by a qualified technician. Ak CAUTION: Before installation, disconnect the battery negative (-) terminal to ^-î-i prevent damage to the unit, fire and/or possible injury . Before beginning any installation, follow these simple rules: 1. Be sure to carefully read and understand the instructions before attempting to install the unit. 2. For safety, disconnect the negative lead from the battery prior to beginning the installation. 3. For easier assembly, we suggest you run all wires prior to mounting your unit in place. 4. Route all of the RCA cables close together and away from any high current wires. Installation 5. Use high quality connectors for a reliable installation and to minimize signal or power loss. 6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle. 7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection. 8. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall. 9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 180" (45.7 cm) of the battery terminal. 10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle. MOUNTING LOCATIONS The mounting position of your amplifier will have a great effect on the sound and performance produced. Engine Compartment Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warrant...
Эта инструкция также подходит к моделям:Автоусилители - DX200.2 (6.73 mb)
Автоусилители - DX2000.1 (6.73 mb)
Автоусилители - DX300.4 (6.73 mb)
Автоусилители - DX500.1 (6.73 mb)