Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Warranty service requests made without proof of date of purchase will be denied. Please keep the original sales receipt for your records and send a copy to request warranty service. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. * ATON is a division of ELAN Home Systems, LLC. ©2007 • All rights reserved. P/N 227948 REV:C Figure 2 Introduction The ATON AIR6 is a small, attractively styled ‘plasma-friendly’ IR receiver designed to fit in-wall electrical boxes (J-Boxes). This receiver uses advanced IR filtering technology which allows it to work even in areas that receive normally harmful interference (near plasma TV’s, compact flourescent lights, etc.). Features (Refer to Figure 1) • Stripped Leads Plus a 4-Conductor Terminal Strip • ‘Plasma-Friendly’ Technology Helps Block Plasma TV Interference • IR Lens Rejects Visible Light Interference • Internal Crosshatch Shield Inhibits EMI/ESI Interference • STATUS Indicator: Green LED for System On/Off indication • ACTIVITY Indicator: Blue LED indicates IR signal activity Figure 1 Specifications: • Requires 12VDC power supply, termination block, and IR emitters for IR operation. • Mounting: Fits in standard single-gang (J-Box) electrical boxes • Power: +12VDC @ 6mA • Carrier Frequency Acceptance Range: 28kHz to 90kHz • Control Range: Up to 35 feet, depending on remote strength and ambient noise conditions • Control Angle: +/- 50 degrees off-axis • Room-to-Room Wire Recommendations: Cat-5 • Maximum recommended cable length: 1200 feet using Cat-5 • Dimensions: 4” (102mm) H x 1.2” (38mm) W x 1” (25mm) D IR Pickup Diode Status LED (Green) Activity LED (Blue) IR Lens 4" (102mm) Front 1-1/2" (38mm) Rear Connection Decora® Style Terminals Insert Plate Stand-Alone System Connections: A: Basic System Figure 2 shows a basic IR distribution system using the ATON AIB4 Amplified IR Connection Block, AIR6 In-Wall IR Receiver, and AIE2 Talk-Back IR Emitters to control source equipment. 1. Pull Cat-5 from the AIR6’s mounting location to the connection terminals of an AIB4 Amplified IR Distribution Block. 2. Connect the Cat-5 wires and IR emitters into the AIB4, as shown. 3. Using the provided screws, mount the AIR6 into a J Box-type electrical box. 4. Set the DIP switches on the AIB4 to LP ON and NET ON or OFF. 5. Plug in the power supply. 6. IR signals sent to the AIR6 will pass through the AIB4 and control the equipment. B: Multi-Room System Figure 3 shows an example of multiple AIR6 IR Receivers in a stand-alone multiroom system. These control the various components in the equipment area. 1. Pull Cat-5 from each room (home runs) to the AIB4 terminator near the controlled components. NOTE: MAX DISTANCE of ALL Wire Runs is 1200 ft using Cat-5 cable. When using long lengths, the dipswitch on the AIB4 must be set to the NET ON position and a 500 Ohm resistor must be used. 2. Connect IR receivers in each room to the Cat-5 runs as shown, using the terminal strips supplied. 3. Connect the Cat-5 wires to the correct location on the AIB4 connection terminals (+12VDC, IR, STATUS, and GND). 4. Install and plug the AIE1 Emitters into the AIB4. 5. Set the DIP switches to LP ON and NET ON. 6. Plug the local AIR5 IR Receiver into the IR RECEIVER jack. 7. Plug in the PS2 12VDC Power Supply. 8. IR signals sent to the AIR6s will pass through the AIB4 and control the equipment. NOTE: Refer to the ATON AIB4 Instructions for power supply considerations and other important information. STATUS Brightness Figure 3 also shows how an external resistor can be added to reduce the brightness of the Status LEDs on ATON IR receivers. In this example, a PS2 12VDC Power Supply is used as the voltage source to indicate ON/OFF status of an A/V Receiver. Choose a resistor value that achieves the brightness you desire (about 2.2k to 12k, 1/8W). Connect it in series with the STATUS lead on each IR receiver, as shown. To 120V AC (unswitched) PS2 Power Supply A/V Receiver Satellite DVD AIR6 In-Wall IR Receiver AIE2 Talk-Back Emitter Rear View Connection Terminals AIE2 Talk-Back Emitter AIE2 Talk-Back Emitter AIB4 Amplified IR Connection Block Figure 2 To 120V AC (unswitched) Power Supply A/V Receiver Satellite DVD AIR6 In-Wall IR Receiver AIR1 Surface-Mount IR Receiver AIR1 AIR5 Tabletop IR Receiver AIE1 Emitter AIE2 Talk-Back Emitter ROOM 1 ROOM 2 ROOM 3 PS2 STATUS Supply To Switched AC Outlet Rear View Add Resistor at each IR receiver to reduce STATUS brightness, if desired. See text. Striped Side STATUS +12V IR OUT GND STATUS +12V IR OUT GND Connection Terminals Wh/Blue IR Blue STATUS Wh/Green +12 VDC Brown GROUND AIB4 Amplified IR Connection Block PS2 or PS3 Surface-Mount IR Receiver Striped Side AIE2 Talk-Back Emitter Connection Block Figure 3 5 Tecnologia al alcance de todos.™ AIR6 Receptor IR empotrado 6 7 8 ©2007 • All rights reserved. P/N 227948 REV:C Tecnologia avanzada para filtrar emisiones infrarrojas [IR] El AIR6 tiene la tecnologia avanz...