Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
NOTE: For a more in depth setting procedure, contact Lightning Audio Technical Support. ADJUSTING CROSSOVER (X-OVER) Turn the crossover adjustment knob all the way down. With the system playing at normal listening level, turn the crossover adjustment knob up slowly until the desired crossover point is achieved. Symptom Diagnosis Remedy Amplifier does not turn on. Amplifier Noise (Turn-On Pop) Engine Noise B+ or REM not between 10.5 and 15.5 volts or no voltage present Amplifier is not properly grounded. Voltage spike from source unit is entering amplifier’s input Noise is radiating into signal cables Check the alternator, battery, fuse, and wiring and repair as necessary Check wiring and repair as necessary Connect turn-on module to REM terminal if pops are eliminated with no input signal to amplifier Re-route signal cables away from sources of high current BOLT COOLING TURBINE The Cooling Turbine delivers large volumes of air over the critical components of your Bolt amplifier. See your local dealer. Installation 1. Remove the four Allen-head screws that attach the Torture Tested logo. 2. Connect the small plug from the Cooling Turbine to the pins marked "FAN" on the PC board inside the amplifier. 3. Using the screws from step 1, secure the Cooling Turbine to the amplifier. Specifications B2.250.1 • Maximum Power: 750 watts • Power Rating: 250w x 1 @ 2ohms 150w x 1 @ 4ohms • Input Sensitivity: 150mV - 4V • High Level Input: 1.5V - 14V • Signal to Noise Ratio: > 90dBA • Channel Separation: 50dB • Crossover Type: Variable 40~130Hz • Amplifier Fuse Value: 15Amp (2) • Chassis Size: 2”H x 11.1”W x 9.8”D B2.150.2 • Maximum Power: 450 watts • Power Rating: 50w x 2 @ 4ohms 75w x 2 @ 2ohms 150w x 1 @ 4ohms • Input Sensitivity: 150mV - 4V • High Level Input: 1.5V - 14V • Signal to Noise Ratio: > 90dBA • Channel Separation: 50dB • Crossover: High/Low/All Pass switch • Crossover Type: Variable 40~400Hz • Amplifier Fuse Value: 25Amp (1) • Chassis Size: 2”H x 11.1”W x 6.9”D B2.200.2 • Maximum Power: 600 watts • Power Rating: 75w x 2 @ 4ohms 100w x 2 @ 2ohms 200w x 1 @ 4ohms • Input Sensitivity: 150mV - 4V • High Level Input: 1.5V - 14V • Signal to Noise Ratio: > 90dBA • Channel Separation: 50dB • Crossover: High/Low/All Pass switch • Crossover Type: Variable 40~400Hz • Amplifier Fuse Value: 30Amp (1) • Chassis Size: 2”H x 11.1”W x 7.5”D B2.300.2 • Maximum Power: 900 watts • Power Rating: 100w x 2 @ 4ohms 150w x 2 @ 2ohms 300w x 1 @ 4ohms • Input Sensitivity: 150mV - 4V • High Level Input: 1.5V - 14V • Signal to Noise Ratio: > 90dBA • Channel Separation: 50dB • Crossover: High/Low/All Pass switch • Crossover Type: Variable 40~400Hz • Amplifier Fuse Value: 20Amp (2) • Chassis Size: 2”H x 11.1”W x 9.8”D B2.350.1 • Maximum Power: 1050 watts • Power Rating: 350w x 1 @ 2ohms 250w x 1 @ 4ohms • Input Sensitivity: 150mV - 4V • High Level Input: 1.5V - 14V • Signal to Noise Ratio: > 90dBA • Channel Separation: 50dB • Crossover Type: Variable 40~130Hz • Amplifier Fuse Value: 15Amp (3) • Chassis Size: 2”H x 11.1”W x 13”D B2.300.4 • Maximum Power: 900 watts • Power Rating: 50w x 4 @ 4ohms 75w x 4 @ 2ohms 150w x 2 @ 4ohms • Input Sensitivity: 150mV - 4V • High Level Input: 1.5V - 14V • Signal to Noise Ratio: > 90dBA • Channel Separation: 50dB • Crossover: High/Low/All Pass switch • Crossover Type: Variable 40~400Hz • Amplifier Fuse Value: 25Amp (2) • Chassis Size: 2”H x 11.1”W x 11.8”D B2.400.4 • Maximum Power: 1200 watts • Power Rating: 75w x 4 @ 4ohms 100w x 4 @ 2ohms 200w x 2 @ 4ohms • Input Sensitivity: 150mV - 4V • High Level Input: 1.5V - 14V • Signal to Noise Ratio: >...
Эта инструкция также подходит к моделям:Автоусилители - B2.150.2 (5.45 mb)
Автоусилители - B2.200.2 (5.45 mb)
Автоусилители - B2.250.1 (5.45 mb)
Автоусилители - B2.300.2 (5.45 mb)