Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Failure to heed the instructions will result in severe injury or death. This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions can result in injury or unit damage. CAUTION: To prevent injury and damage to the unit, please read and follow the instructions in this manual. We want you to have enjoyment from this system, not a headache. CAUTION If you feel unsure about installing this system yourself, have it installed by a qualified Lightning Audio technician. CAUTION Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury. ! ! ! 4 Design Features Installation JUICE BOOST JUICE BOOST OUTPUT INPUT PROTECT POWER L LF LR R RF RR GAIN GAIN MIN MAX MIN MAX LF.RF X-OVER X-OVER LR.RR 40 400 40 400 50Hz 0dB 12dB 50Hz 0dB 12dB FILTER FLAT HIGH LOW FILTER FLAT HIGH LOW HI INPUT HI INPUT + L - +R - + L - +R - 30A 30A FUSE + RR - + LR - + RF - + LF - + 12V REM GND + BRIDGED - + BRIDGED - JUICE BOOST JUICE BOOST OUTPUT INPUT PROTECT POWER L LF LR R RF RR GAIN GAIN MIN MAX MIN MAX LF.RF X-OVER X-OVER LR.RR 40 400 40 400 50Hz 0dB 12dB 50Hz 0dB 12dB FILTER FLAT HIGH LOW FILTER FLAT HIGH LOW HI INPUT HI INPUT + L - +R - + L - +R - 25A 25A FUSE + RR - + LR - + RF - + LF - + 12V REM GND + BRIDGED - + BRIDGED - B2.300.4 B2.400.4 A. High Level (Speaker) Inputs: The high level inputs use a detachable connector terminated with 20 AWG leads. These inputs should be used if the source unit has only speaker line (high level) outputs and not RCA outputs. B. RCA Input Jacks – Line Level from Radio Pre-outs: The industry standard RCA jack provides an easy connection for signal level input. They are gold-plated to resist the signal degradation caused by corrosion. C. Gain Control: The input gain control is preset to match the output of most source units. They can be adjusted to match output levels from a variety of source units. D. Crossover Filter Switch: High for High Pass - Mid-Tweeter. Off for All Pass - Full Range. Low for Low Pass - Subs. E. Speaker Connections: Follow correct polarity, and do not Ground any speaker wires. Do not connect any speaker wires together. F. Power Connector terminals: Connects Power, Ground, and Remote G. Power Fuse: If this Fuse should blow, determine the cause or see your authorized dealer. Never replace the fuse with one of greater value than the original H. Adjustable Crossover Frequency Control: 40-400Hz (40-130Hz on Mono Amplifier). I. Juice Boost Switch: Applies 12dB of 50Hz Bass Boost. Adjustable on B2.350.1 Mono Amplifier. J. Pass Thru Outputs: The Pass-Thru provides a convenient source for daisy-chaining an additional amplifier without running and extra set of RCA cables from the front of the vehicle to the rear amplifier location. K. Remote Juice: Connection for remote juice control (B2.350.1 Only). INSTALLATION CONSIDERATIONS The following is a list of tools needed for installation: Volt/Ohm Meter Wire strippers Wire crimpers Wire cutters #2 Phillips screwdriver Battery post wrench Hand held drill w/assorted bits 1/8" diameter heatshrink tubing Assorted connectors Adequate Length—Red Power Wire Adequate Length—Remote Turn-on Wire Adequate Length—Black Grounding Wire Installation This section focuses on some of the vehicle considerations for installing your new Amplifier. Pre-planning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments. ! ! CAUTION: If y...
Эта инструкция также подходит к моделям:Автоусилители - B2.150.2 (5.45 mb)
Автоусилители - B2.250.1 (5.45 mb)
Автоусилители - B2.300.2 (5.45 mb)
Автоусилители - B2.300.4 (5.45 mb)