Оценок - 6, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
CAUTION: These amplifiers are not recommended for impedance loads below ! 2. stereo and/or 4. bridged (mono). SPEAKER 12V 15A 15A REM GND FUSE + + - JUICE BOOST X-OVER GAIN PROTECT INPUT POWER L L R HI INPUT 0dB 12dB 40 250 MIN MAX + - +R - JUICE BOOST INPUT PROTECT POWER GAIN MIN MAX X-OVER FILTER 40 400 FLAT 50Hz HIGH LOW 0dB 12dB L HI INPUT + - +R - L 25A FUSE SPEAKERS + 12V REM GND + - + R - + BRIDGED - L 25A FUSE SPEAKERS + 12V REM GND + - + R - + BRIDGED - Power Connection CAUTION: Use only one input configuration. Using both the RCA and High Level inputs will cause undesirable operation. ! *NOTE: When using High Level Inputs, if audible engine noise is present, connect the Black wire to chassis ground. If noise is still present, contact your local authorized dealer or Lightning Audio customer service. Installation REMOTE JUICE CONTROL (B2.350.1 Only) Mounting and installation 1. Find a location, either under the dash or near the center console, that gives easy access to the remote. 2. Using the screws supplied, install the remote. 3. Route the cable for the remote and connect to both the remote and amplifier. USING PASSIVE CROSSOVERS A passive crossover is a circuit that uses capacitors and/or coils and is placed on speaker leads between the amplifier and speaker. The crossover delegates a specific range of frequencies to the speaker for optimum driver performance. A crossover network can perform one of three functions: High-Pass (capacitors), Low-Pass (inductors or coils) and Bandpass (combination of capacitor and coil). The most commonly used passive crossover networks are 6dB/octave systems. These are easy to construct and require one component per filter. Placing this filter in series with the circuit will reduce power to the speaker by 6dB/octave above or below the crossover point depending on whether it is a high-pass or low- pass filter. More complex systems such as 12dB/octave or 18dB/octave can cause impedance problems if not professionally designed. Passive crossovers are directly dependent upon the speaker's impedance and component value for accuracy. When passive crossover components are used in multiple speaker systems, the crossover's effect on the overall impedance should be taken into consideration along with the speaker's impedance when determining amplifier loads. L C 6dB/Octave Low-Pass 6dB/Octave High-Pass Freq. Hertz Speaker Impedance 2 OHMS 4 OHMS 8 OHMS L C L C L C 80 4.1mH 1000.F 8.2mH 500.F 16mH 250.F 100 3.1mH 800.F 6.2mH 400.F 12mH 200.F 130 2.4mH 600.F 4.7mH 300.F 10mH 150.F 200 1.6mH 400.F 3.3mH 200.F 6.8mH 100.F 260 1.2mH 300.F 2.4mH 150.F 4.7mH 75.F 400 .8mH 200.F 1.6mH 100.F 3.3mH 50.F 600 .5mH 136.F 1.0mH 68.F 2.0mH 33.F 800 .41mH 100.F .82mH 50.F 1.6mH 26.F 1000 .31mH 78.F .62mH 39.F 1.2mH 20.F 1200 .25mH 66.F .51mH 33.F 1.0mH 16.F 1800 .16mH 44.F .33mH 22.F .68mH 10.F 4000 .08mH 20.F .16mH 10.F .33mH 5.F 6000 51mH 14.F .10mH 6.8.F .20mH 3.3.F 9000 34mH 9.5.F 68mH 4.7.F .15mH 2.2.F 12000 25mH 6.6.F 51mH 3.3.F 100mH 1.6.F L = Low-Pass (Inductor) C = High-Pass (Capacitor) For more information, see your Authorized Lightning Audio Dealer. ! CAUTION: The Lightning Audio amplifiers are not recommended for impedance loads below 2. stereo and 4. bridged (mono) loads. 9 Troubleshooting Accessories Operation ADJUSTING GAIN To adjust the gain setting, turn the amplifier gains all the way down. Turn the source unit volume up until distortion is audible and then turn it down a bit until the distortion is inaudible. Next, turn the amplifier gain setting until once again distortion is audible and then back it down until the...
Эта инструкция также подходит к моделям:Автоусилители - B2.150.2 (5.45 mb)
Автоусилители - B2.200.2 (5.45 mb)
Автоусилители - B2.250.1 (5.45 mb)
Автоусилители - B2.300.2 (5.45 mb)