Оценок - 5, средний балл: 4.6
(
)
)
|
Фрагмент инструкции
Speaker Impedance 2 (Sim 2 Ohm 2 Ohm 2 Ohm T.H.D 0.04% 0.04% 0.04% 0.04% Frequency Response i5Hz~35kHz, - ldB 15HZ-35ICHZ, - ldB !5Hz-35kHz, - ldB i5Hz-35kHz, - ldB Input Sensitivity ioomV-4c>oomV i00mV-4000mV ioomV-400omV i00mV-4000mV Input Impedance 22 kOhm 22 kOhm 22 kOhm 22 kOhm S/N Ratio >90dB >9odB >9odB >9odB Channel Separation >65dB >65dB >65dB >65dB Crossover Filters Low Pass High Pass Bandpass 40Hz-350kHz 4oHz-3kHz n/a 40Hz-350kHz 40HZ-3 kHz n/a 40Hz-350kHz 4oHz-3kHz n/a 40Hz-350kHz 40HZ-3 kHz n/a Bass Boost +l8dB +l8dB +l8dB +i8dB Dimensions (Inches) 10.25 x 2 x 8 [WxHxL) 10.25 x 2 x 10 (WxHxL) 10.25 x 2 x 12 (WxHxL) 10.25 x 2 x 15 (WxHxL) Fuse(s) 15A 20A 25A 15AX2 Vlbe251 amplifier6* vibe26l fmCp,|fierel Vibe411 amplifier** Vibe421 amplifier^ Vibe431a4mphiifinenre' vibe53ia5mcPhilfienrel 2X400W 2 x 600W 4X75W 4 x 125W 4 x 150W 4 x 100W + 1 x 200W 2*8oqW 2x1200W 4 x 15QW 4 x 250W 4X30QW 4X200W+IX400W 1 x 1600W 1 x 2400W 2X300W 2 X 500W 2 x 600W 2 x 400W +1 x 600W 2 x 650W 2 X lOOOW 4 x 125W 4 x 200W 4 x 250W 4X175W+IX375W 2 Ohm 2 Ohm 2 Ohm 2 Ohm 2 Ohm 2 Ohm 0.04% 0.04% 0.04% 0.04% 0.04% 0.04% i5Hz-35kHz, - ldB i5Hz-35kHz, - ldB i5Hz-35kHz, - ldB i5Hz-35kHz, - ldB i5Hz-35kHz, - ldB i5Hz-35kHz, -ldB iCK)mV-40oomV i00mV-4000mV ioomV-40oomV i00mV-4000mV !0omV-4O00mV i00mV-4000mV 22kOhm 22 kOhm 22 kOhm 22 kOhm 22 kOhm 22 kOhm >godB >godB >9odB >90dB >9odB >90dB >65dB >65dB >65dB >65dB >65dB >65dB 40Hz-350kHz 8oHz-2.5okHz n/a 40Hz-350kHz 40HZ-3 kHz n/a 40Hz-350kHz 40HZ-3 kHz n/a 40Hz-350kHz 40HZ-3 kHz n/a 40Hz-350kHz 40HZ-3 kHz n/a 40HZ-500HZ 40Hz-4kHz variable, 40Hz-4kHz(HPF) 40Hz-500Hz(LPF) +i8dB +i8dB +l8dB +i8dB +i8dB +i2dB 10.25 x 2 x 19 (WxHxL) 10.25 x 2 x 21 (WxHxL) 10.25 x 2 x 12 (WxHxL) 10.25 x 2 x 14 (WxHxL) 10.25 x 2 x 17 (WxHxL) 10.25 x 2 x 24 (WxHxL) 25AX2 40Ax2 15AX2 20A X 2 25AX2 30A X 2 I N S TA L LAT IO N 1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39") in length. Use 8 gauge wire. 5. Connect the remote terminal to the remote output of the head unit using 14 gauge wire. 6. Connect an empty fuse holder within 300 mm (12") of the battery and run 8 gauge or larger high quality cable from this fuse to the amplifier location. 7. Make sure there is no fuse in this fuse holder. Then make the connection to the "BATT" connection on the amplifier. 8. If multiple amplifiers are being used, use cables (each with its own fuse at the battery) or a #0 or #2 cable from the fuse holder at the battery to a distribution block at or near the amplifier's location. 9. Connect all line inputs and outputs using high-quality RCA-RCA cables. 10. Insert fuse(s) at the battery fuse holder(s). 11. Recheck all connections before powering up. ...
Эта инструкция также подходит к моделям:Автоусилители - VIBE211 (763.04 kb)
Автоусилители - VIBE221 (763.04 kb)
Автоусилители - VIBE231 (763.04 kb)
Автоусилители - VIBE241 (763.04 kb)