Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
. If no car circuits are rated high enough, connect the unit directly to the battery. Parts list . The numbers in the list correspond to those in the instructions. . The bracket . is attached to the unit before shipping. Before mounting the unit, use the release keys . to remove the bracket . from the unit. For details, see “Removing the bracket (.)” on the reverse side of the sheet. . Keep the release keys . for future use as they are also necessary if you remove the unit from your car. . The screws . and frames . are attached to the unit before shipping. For details, see “Adjusting the frames (.)” on the reverse side. . For XAV-701BT only: Assemble the parts of the microphone . before use. For details, see “Installing the microphone (XAV-701BT only) (.)” on the reverse side. Caution Handle the bracket . carefully to avoid injuring your fingers. . Catch Note Before installing, make sure that the catches on both sides of the bracket . are bent inwards 3.5 mm (5/32 in). If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. Connection example Notes (.-A) . Be sure to connect the ground (earth) lead before connecting the amplifier. . The alarm will only sound if the built-in amplifier is used. Note (.-B) You cannot use multiple auxiliary devices simultaneously, even if they are connected to different terminals. Connection diagram . To a common ground (earth) point First connect the black ground (earth) lead, then connect the yellow and red power supply leads. . To the power antenna (aerial) control lead or the power supply lead of the antenna (aerial) booster Notes . It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). . If your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. . To a car’s illumination signal Be sure to first connect the black ground (earth) lead to a common ground (earth) point. . To the +12 V power terminal which is energized when the ignition switch is set to the accessory position Notes . If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to first connect the black ground (earth) lead to a common ground (earth) point. . If your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.” . To the +12 V power terminal which is energized at all times Be sure to first connect the black ground (earth) lead to a common ground (earth) point. . To the parking brake switch cord . To an auxiliary device such as a portable media player, game console, etc. (not supplied) Tip You can use an RCA pin cord (not supplied) to connect auxiliary devices. . To the +12 V power terminal of the car’s rear lamp lead (only when connecting the rear view camera) Notes on the control and power supply leads . REM OUT lead (blue/white striped) supplies +12 V DC when you turn on the unit. . If your car has built-in FM/AM antenna (aerial) in the rear/side glass, connect REM OUT lead (blue/white striped) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. . A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection . Before connecting the speakers, turn the unit off. . Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid damage. . Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speakers. . Do not connect the ground (earth) lead of this unit to the negative (–) terminal of a speaker. . Do not attempt to connect the speakers in parallel. . Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. . To avoid a malfunction, do not use the built-in speaker leads installed in your car if they feature a common negative (–) lead for the right and left speakers. . Do not connect the unit’s speaker leads to each other. Notes on connection . If “Output connection failure.” appears in the display, make sure the speaker and amplifier are connected correctly. . To use the monitor for the rear seats, connect the parking brake switch cord to the ground (earth). FRONT AUDIO OUT SUB OUT REAR OUT Z.Z L / R REAR AUDIO OUT AUX IN ( VIDEO ) AUX AUDIO IN CAMERA * not supplied Video camera* A B 4-422-719-11(1) Installation/Connections AV Center XAV-701BT/XAV-741 Equipme...
Эта инструкция также подходит к моделям:Автомобильное видео - XAV-701BT (333.85 kb)