Оценок - 3, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
*4 RCA pin cord (not supplied) *5 For details on connecting to the parking brake switch cord, see “Connecting the parking brake lead (.)” on the reverse side. *6 not supplied *7 The sound is output from this terminal only when ZONE x ZONE is activated. This terminal outputs a fixed level regardless of the volume control of the unit. *8 A separate adaptor may be required. *9 USB connection cable RC-202IPV (not supplied). To connect an iPod via RC-202IPV, make sure to connect the video output plug to AUX1 IN. MIC IN*3 AUX2 AUDIO IN Z.Z L / R*7 REVERSE IN CAMERA REAR OUT REMOTE IN*8 SUB OUT EXT AUX1 AUDIO IN FRONT AUDIO OUT REAR AUDIO OUT AUX2 IN AUX1 IN Fuse (10 A) . From car antenna (aerial) *4 . REM OUT Max. supply current: 0.4 A ILLUMINATION *5 PARKING BRAKE Blue/white striped White Green Purple White/black striped Gray/black striped Green/black striped Gray Purple/black striped Red Yellow Black Orange/white striped Light green .*2 *4 *6 *9 *4 *4 *4 *4 (XAV-701BT only) . 2 . . . . . 8 . . . 2 . 2 *1 *9 XAV-701BT XAV-701BT only Left Right Left Right Precautions . Choose the installation location carefully so that the unit will not interfere with normal driving operations. . Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts. . Use only the supplied mounting hardware for a safe and secure installation. . To open/close the front panel smoothly, insert/eject a disc easily, and especially to drive safely, a certain distance between the front panel and the shift lever is necessary. The necessary distance differs, depending on the shift lever position of your car. Before installing the unit, choose the installation location carefully so that you can drive safely. Shift lever 87 mm (3 1/2 in) Mounting angle adjustment Adjust the mounting angle to less than 45°. Connecting the parking brake lead Be sure to connect the parking brake lead (light green) of the power supply connection cable . to the parking brake switch cord. The mounting position of the parking brake switch cord depends on your car. Consult your car dealer or your nearest Sony dealer for further details. Installing the microphone (XAV-701BT only) To capture your voice during handsfree calling, you need to install the microphone .. Cautions . Keep the microphone away from extremely high temperatures and humidity. . It is extremely dangerous if the cord becomes wound around the steering column or gearstick. Be sure to keep it and other parts from obstructing your driving. . If airbags or any other shock-absorbing equipment is in your car, contact the store where you purchased this unit, or the car dealer, before installation. Parking brake switch cord Foot brake type Parking brake switch cord Hand brake type A 1 2 B 1 2 b a b a a b Clips (not supplied) c a b Clip (not supplied) . . . Face the hook inwards. . . Dashboard . Claws A 1 2 3 B . Larger than 182 mm (7 1/4 in) Larger than 111 mm (4 3/8 in) To the dashboard/center console Bracket Parts supplied with your car Size: 5 . max. 8 mm (7/32 . max. 5/16 in) Size: 5 . max. 8 mm (7/32 . max. 5/16 in) . . Bracket .-A Installing on the sun visor 1 Install the microphone a on the clip b . 2 Install the clip b on the sun visor. 3 Install clips (not supplied) and adjust the length and position of the cord so that it does not obstruct your driving. .-B Installing on the dashboard 1 Install the microphone a on the clip b , then place the cord along the groove of the clip b . 2 Attach the clip b to the dashboard with the double-sided tape c . 3 Install a clip (not supplied) and adjust the length and position of the cord so that it does not obstruct your driving. Notes . Before attaching the double-sided tape c , clean the surface of the dashboard with a dry cloth. . Adjust the microphone angle to the proper position. . The microphone a can be installed without using the clip b . In this case, directly attach the microphone to the dashboard with the double-sided tape c . Keep the unused clip b for future use. Removing the bracket Before installing the unit, remove the bracket . from the unit. 1 Insert both release keys . together between the unit and the bracket . until they click. 2 Pull down the bracket ., then pull up the unit to separate them. Adjusting the frames You can adjust the projecting part of the unit when the unit is mounted. Shift lever Projecting part 1 Remove the screws . from both sides of the unit. 2 Choose a screw hole from ., . or . on each frame .. If you secure the frames . with the screw holes . (default position), it will maximize the projecting part of the unit. On the other hand, screw holes . will minimize the projecting part. 3 Reattach the frames . with the selected screw holes with the removed screws .. Notes . Choose the same screw hole position on both frames. . If you intend to secure the frames with screw holes . or ., make sure that there is enough space in the dashboard of your car ...
Эта инструкция также подходит к моделям:Автомобильное видео - XAV-741 (333.85 kb)