Bright transmitter LED's indicate operation and monitor battery condition. (Page 15) Deluxe Wall Push Button Station: A feature-packed accessory unit, Allstar's Deluxe Wall Push Button Station allows access to all of the Opener'sfunctions. The Opener's built-in light can be turned on or off independent of door operation. A Vacation Switch allows the Opener to be deactivated for extended periods of time. Lighted Push Buttons enhance nighttime use. (Page 16) Keyless Entry System: A tamper resistan

A small Plastic Pin is provided to secure the other end of the Receiver to the panel. For proper operation, the Antenna Wire should be POINTED STRAIGHT DOWN toward the floor. After installing the Radio Controls, check their operation by moving approximately 35 FT away from the garage door and pressing the Transmitter Button. Operation at this distance should be reliable. If the Transmitter doesn't activate door operation, check that all Coding Switches are set identically. If the operational dis

Close the door. If the down force adjustments are correct, the door will reverse within two seconds of contacting the object and travel to the Full Open position. If this does not occur, recheck the Limit Adjustments (Page 17) and Sensitivity Adjustments (Step 2 & 3, Above). NOTE: Any time adjustments are made to Limits or Sensitivity, YOU MUST RETEST THE OPENER FOR THE REVERSING FEATURE AT FLOOR LEVEL AS OUTLINED ABOVE. OPEN FORCE ADJUSTMENT CLOSE FORCE 104391 ADJUSTMENT 1 1/2” BLOCK OF WOOD LA

2 Product Features ................................................................................... 2 Component Identification/Tools Required ........................................... 4 Section A: Assembly Instructions ....................................................... 5 Section B: Installation Notes ................................................................ 6 Section C: Installing the Operator ....................................................... 7 Identify Your Door Type ....

Use a minimum 22 gauge solid "trace" wire for interconnect. C. Run a wire pair (20 or 22 gage solid wire) from the receiver position (unit with "LED" light in the front, may be either side of the door) back to the rear bulkhead of the garage door opener. NOTE: Leave about 12” of extra wire at the receiver end and about 24” of extra wire at the opener end. D. Strip approximately 5/16” from each wire end at the photosystem units and at the opener. E. Using two (2) wire nuts (supplied), connect the

If the down force adjustments are correct, the door will reverse within two seconds of contacting the object and travel to the Full Open position. If this does not occur, recheck the Limit Adjustments (Page 17) and Sensitivity Adjustments (Step 2 & 3, Above). NOTE: Any time adjustments are made to Limits or Sensitivity, YOU MUST RETEST THE OPENER FOR THE REVERSING FEATURE AT FLOOR LEVEL AS OUTLINED ABOVE. OPEN FORCE ADJUSTMENT CLOSE FORCE 104391 ADJUSTMENT 1 1/2” BLOCK OF WOOD LAID FLAT (2”X4”)

A. Remove the access cover from the front of the transmitter by sliding the cover away from the top of the transmitter. (See Fig. 1A). B. Use a small screwdriver or knife to remove small door on back of receiver to gain access to coding switches. (See Fig. 1B) IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION. Note: If installing Allstar Classic Quik Code transmitter(s) with a 99xx or 88xx Allstar Rece

Models 9931, 8832, 8833: The coding switch in these models consist of eight or nine small switches, each of which can be placed in any of three different positions. (+, 0, -). See Fig. 2. Using a small screwdriver, set both the transmitter and receiver coding switchesidentically. (Your private code setting). DO NOT SET ALL THE SWITCHES IN THE SAME POSITION. EXAMPLE: FIGURE 2 NOT ALL + or 0 or - IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS

See Fig. 4. Replace the pushbutton wiring and tighten the screws. Be certain the antenna wire is hanging down vertically and the receiver terminal numbers printed on the receiver case match the numbers on the operator terminal strip. (1) D. Model 8832 - Double Door Garage 3 2 1 3 2 1 3 2 1 3 2 1 (2) (1) E. Model 8833 - Three Door Garage (1) (3) (2) 3 2 1 3 2 1 3 2 1 FIGURE 5 104388 B. If the operating distance drastically decreases, remove the battery access door See Fig. 1A, and replace the bat

After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 35 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. B. If the transmitter doesn’t activate the operator, check the coding switches on both the transmitter and receiver to assure an “exact” match. ( See Fig. 2 & 3) . This may necessitate a reprogramming of a Quik Code Classic transmitter to match the receiver coding swi