Войти:
Скачали: 0   Размер: 107 kb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

Painting Your Garage Door suRfACE PREPARATION fOR PAINTING Wax on the surface must be removed or paint peeling/ flaking will result. To remove this wax, it will be necessary to lightly scuff the surface with a fine steel wool pad saturated with soapy water. A final wipe and rinse should be done with clean water only to remove any loose particles and any soapy film residue. Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded with 0000 steel wool or no. 4

Скачали: 5   Размер: 107 kb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

Ensure the door rollers are rotating freely when opening and closing the door. If rollers do not rotate freely, clean the door tracks, removing dirt and any foreign substances. Clean and lubricate (use a non-silicon based lubricant) hinges, steel rollers and bearings. DO nOT lubricate plastic idler bearings, nylon rollers, door track. DO nOT oil a cylinder lock, if actuation is difficult use a graphite dust to lubricate. 6 Please Do not Return This Product To The Store. Contact your local Wayne-

Скачали: 0   Размер: 107 kb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the find a Dealer section online at Attaching hor Tracks to Q.I. flag Angles Tools: Ratchet wrench, 9/16” Socket, 9/16” Wrench, level, Step ladder 14 NOTE: If you have Q.I. flag angles, complete this step. To install horizontal track, place the curved end over the top roller of the top section. Align key slot of the horizontal track with the Q.I. tab of the flag angle. Push curved portion of horiz

Скачали: 9   Размер: 768 kb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

This manual MUST be attached to the wall in close proximity of the door. WINDLOAD RATED DS-350 COMMERCIAL ROLL-UP DOORS INSTALLATION INSTRUCTIONS ©Copyright 2002 Wayne-Dalton Corp. P/N 291341, DOC #101-0093-1 REV 02 IMPORTANT SAFETY NOTICES Read the enclosed instructions carefully before attempting installation. If there are any questions about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. 1. Operate the door ONLY when it is

Скачали: 0   Размер: 909 kb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

Using a ratchet wrench with a 5/8” (16mm) socket (NOTE: A 3” (76mm) extension is also recommended for added clearance from the horizontal angle), wind the spring by rotating the winding shaft counter clockwise, while watching either the black tooth on the ratchet wheel or the mark on the winding shaft. Important : paw l knob must be in upper position to add/ remove required number of spring turns. After 2-3 turns, remove the ratchet wrench and adjust the cable on the left side. Ensure counterbal

Скачали: 1   Размер: 909 kb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

Wayne-Dalton highly recommends that you read and fully understand the Installation Instructions and Owner’s Manual before you attempt this installation. To avoid possible injury, read the enclosed instructions carefully before installing and operating the garage door. Pay close attention to all warnings and notes. After installation is complete, fasten this manual near garage door for easy reference. The Quick Start Guide and Installation Instructions and Owner’s Manual are available at no charg

Скачали: 1   Размер: 909 kb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

for single spring applications, there will be no left hand spring in the TorqueMaster ® spring tube assembly. lift the TorqueMaster® spring tube assembly and rest it on top of the flag angles. NOTE: Cable drum assemblies are marked right and left hand and consist of a cable drum and drum wrap. Cable drums and TorqueMaster® spring tube assembly are cam shaped to fit together only one way. Starting on the right hand side, slide the drum wrap over to access the counterbalance cable. Pre-wrap the ca

Скачали: 0   Размер: 1 mb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

At this price point, the construction provides a substantially higher thermal efficiency than industry standard polystyrene doors. The Wayne-Dalton Thermospan Series doors are the only doors in the industry with patented, roll-formed integral struts on each section, making them the most rigid doors available. WAYNE- DALTON COMMERCIAL DOOR SYSTEMS • EXCEPTIONAL THERMAL QUALITIES (R-VALUE = 10.79, U-VALUE = 0.093) • STANDARD SIZES UP TO 16’ 2” WIDE AND 16’ 1” HIGH • COMPETITIVELY PRICED • COMMERCI

Скачали: 0   Размер: 2 mb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

Attach to section using (2) 1/4”-20 x 7/8” self drilling screws at each end and center stile location. To attach a u-bar across the lower leaf of hinges with strut clips: Remove 1/4”-20 x 7/8” self drilling screws from lower leaf of hinges along sections which a u-bar will be attached to. Place u-bar above across hinges and attach to section with strut clips and the 1/4”-20 x 7/8” self drilling screws which were removed. 8300 LT-coM Aluminum Strutting Schedule---White, Almond, and Taupe colored

Скачали: 0   Размер: 2 mb   Производитель: Wayne-Dalton  
Категория: Автоматические ворота
@name

Mark a vertical pencil line on the mounting surface above the door, at the center. Measure from the center of the bearing, in one of the end bearing brackets, downwards, to the top the door. Using that measurement, measure that distance upwards from the top of the door to the mounting surface, and mark a horizontal pencil line which intersects the vertical pencil line. Align the edge of the center bearing bracket with the vertical pencil line and the center of the bearing in the center bearing b





Категории