Оценок - 3, средний балл: 3.3 ( )

Производитель: Wayne-Dalton Размер: 4.85 mb Название файла: Язык инструкции:

Press and release the PROGRAM button located on the garage door opener. The red PROGRAM STATUS light on the opener unit and the overhead lamp will turn on and remain lit for one minute, indicating activation of the learn mode. 2. Press one of the buttons on the transmitter you wish to use to operate the door. The PROGRAM STATUS light on the opener will turn on and off three times indicating a successful learn. 3. Press the same button on the transmitter once more to confirm operation. The opener will turn on and move the door. At this point you will be able to activate the opener. WALL STATION: 1. Press and release the PROGRAM button located on the garage door opener. The red PROGRAM STATUS light on the opener unit and the overhead lamp will turn on and remain lit for one minute, indicating activation of the learn mode. 2. Press the light on/off button on the wall station. The program status light will turn on and off three times indicating a successful learn. 3. Press the light on/off button on the wall station once more to confirm operation. The overhead light will toggle from on to off and from off to on. At this point you will be able to activate the opener. Program Status LED Program Button Programming Wireless Wall Station(s) Or Transmitter(s) to Opener Tools Needed: None Right Side Of Opener FORCE ADJ. STATUS SW PROGRAM WARNING .. To Operate DoorPress Here Light Button Wall Station Large Button Transmitter .... Monthly Maintenance: 1. Lubricate hinges and rollers of garage door. 2. Inspect the door for loose fasteners, worn or frayed counterbalance cables and the presences of legible safety labels/ tags. Have repairs made by a qualified service person. Contact customer assistance for free replacement safety labels/ tags. 3. With door fully closed, pull down on the emergency disconnect to manually operate the door. If the door feels unbalanced or binds, have a qualified service person make necessary adjustments or repairs to the door. 4. Perform the contact/obstruction tests. See Steps 21 and 22 for the contact/obstruction test instructions. If door/opener fails contact/ obstruction test reset the door close limits according to the instructions in Step 19, adjusting until door reverse on contact with a 2 x 4 board laid flat on the garage floor. If opener still fails, have a qualified service person make adjustments/repairs or this could result in severe or fatal injury. 5. Failure of door/opener to respond to transmitter, multi-function wall station or wireless keyless entry may be due to a weak or dead battery. Replace the battery. Maintenance Twice a Year: Check chain tension. If chain rests on bottom of rail, adjust tension by turning the two chain adjusting nuts at the end of the rails (opposite the opener end) clockwise. Make sure to adjust both nuts equal amounts and until chain is approximately 1/2” above the bottom of rails when measured in the middle of the rail length. Battery Replacement for Wall Station: Remove the battery cover completely (right-hand side of wall station) by disengaging the battery cover’s lower clip; remove the remove the old batteries. Install two AAA batteries into the wall station observing the polarity, (+) and (-), of both batteries. After a few seconds, the red LED will begin to blink every three seconds. If it is desired to slow the LED blink rate refer to the wall station operation section on page 28 “Backlit LED Lights”. Re-install the battery cover by first inserting its top into the wall station then inserting and securing its bottom. Note: Use only two AAA batteries. Note: Dispose of dead batteries properly. Battery Replacement for Transmitter: Insert a coin in the coin slot of the transmitter and twist coin to access the dead battery. Replace the battery, being careful to match the positive (+) symbols on the circuit boards with the battery; snap case back together. Note: Transmitters use (1) CR2016 or equivalent battery. Note: Dispose of dead battery properly. Battery Replacement for Wireless Keyless Entry: To change battery, snap open case with a coin and remove old battery. Replace the battery, being careful to match the positive (+) symbols on the circuit boards with the battery; snap case back together. Note: Keyless entries use (1) CR2032 or equivalent battery. Note: Dispose of dead battery properly. Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at Troubleshooting SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Opener won’t work from wall button or radio control. No power to opener. Short circuit in wires to opener or wall button. Motor Protector trips open due to excessive use. Check cord to outlet, wall switch and circuit breaker. Isolate by disconnecting the wires at the opener from the wall station. Allow motor to cool for 20 minutes and try again. Open...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: