Оценок - 1, средний балл: 5 ( )

Производитель: Craftsman Размер: 7.32 mb Название файла: Язык инструкции:

Step 10, page 22 -Alternate floor mounting of the safety reversing sensor will require hardware that is not provided. Step 11, page 25 _ Generally, a one pie_ door does not require reinforcemenL tf your door is lightweight, you _e refer to the information relating to section_ doors on page 24. ,,Step 11, page 25 _Depending on your dooCs construction, you might need additional mounting hardware for the door brackeL oDo you have an a_ess door in addition to the garage dc_r? if not, Model 53702 Emergency Key Release is required. See page 38 , The gap between the bo_om of the garage door and the floor cannot exceed 1/4". Otherwise, the safety reverse system may not work properly. See page 30. The floor or the door should be repaired One-Piece Door With Track You may find it helpful to refer back to this page as you proceed with the installation of your o_ner. Opener CaAon Inventory Your garage door o2_ner is packaged in two ca_ons which contain at_pa_s illustrated b@[ow, _fanylhing is missing_ carefu!!y check the packing matedaL PaAs may be "stuck" in Me foam_ Hardware for assembly and installation is shown on page 7 5_25 ('9, 5_5 (1) Ugh_ed C4_ M_._ S[_24 or'4y M_x_ieb 93225 Model 5_ e._y Compa_ R_o{e C_tt_ _4ea_r Bt_ke_ S4sfe_yRevergr_ .s_50{ _@ua_ng Bta_ V_4_hSquare H_@_ (2} C_'_aimar_8 C@lm Arm _ Safety Revers_g Sen_ Wth S_ (2) 6 Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation procedures. AssembLy Hardware T_o_ey ThCe_d_ Sh_ (1} _16 _ {4} I/4 _ 20 _ 7/16 _ (4} Installation Hardware H_,_d_ R_t Gte_ ,,.-'_1.*_8 _ _o;b__ (4) NL4 _ _8i6t Ro?e Safety Reversing Sensor Installation Hardware Ca_ge _Rs _/4"-20 . 1_" (4) Lo_ N_ _/4" _ (4) _,/i#g N_ (2) Hex _._w i/_-20 _ 11_" (2) Assembly Section: Pages 8-11 To avoid installation d:mcu[ties, do not run the gauge d_r opener until :nst_ to do so. , Align _e 3 Torai_se_ons on a fiat suRace exactty as shown° The end sections are identical Make sure the "arrow labet ° on the center se_ion is pointing toward the door.. , Inse_ the carnage bolts so the square bolt necks seat in the square holes in the T-rai! end sections and pass through the round holes in T_rait center section. Assemble lock nuts, ensure alignment and Ma_ sure _ n_ks are tig_en i_k nuts {_ o_ratJon, nef_ anddOr aa_n_ d_ re_r_lm Hardware Shown Actual S:ze % END of "T _a_l , Pos_on #_e_ble putiey bracket on #_efront end:of the T_raii as shown Fasten s_cure_yv_4th_e hardware, _16 _ 18.;7/8" Sd!6_ 18 _1_ Whe_ t_ghte_ing _e sorews_ tO t_he rail Otherwise, the whe_ o_aer _s Hardware Shown Assembly Step 2 Actua_ Size Install the Trolley on the T_ra# -Attach the threaded sha_ to the trotley wi_ the I_xckwasher and nuts as shown Trolley L._k W_;_t Nut _'16" _1_ _ ,,18 Assembly Step 3 Fasten the T-rail to the Opener Place the opener on packing material to protect the cover. For coevenience, pat a support under the came pui_ey brackeL Remove the (2) 5/I6_18.1/2 _ washered _rews mounted in the top d the opener_ -Atign the holes in the back seGion of the %r'ai_ with the holes in the opener. * Fasten the rail with _e (2) washer_J screws previously remove& Tighten securely. Remember to use only these screwsf Any other screws wil! cause serious damage to the opener. lnse_ a 5/16"-18x7/8" hex screw stop hole in the T.-rail as shown. Tighten securely with a 5116_lock washer and nuL This screw limits trolley travel in the UP direction. Hardware Shown Actual Size Hex _tew Nut L._ Wa#_e_ As a tem_rary stop. insed a screwdnver into the hole in the front end d the %rait. Slide the trolley assembly _ong the rail to the screwdriver stop if trolley hits against any nuts on the T_rai_,the bolts and Ruts were attached from the wrong side and must _ reposittoned. Review Step 1. To fasten rail, use only those screws mounted in the top of the opener. Any other screws will cause serious damage to the opener. Was_e_e_J _.ew 9 Assembly Step 4 Install the Chain/Cab@ & Attach the Sprocket Cover Figure 2 o_ _OCkef Detach the came loop from the capon and fasten it to the tro!fey with a master link from #Behardware bag See master link procedure, Figure 'I, F_gure 3 WiSh the trolley against the serewdnvec dispense Ma$_er Unk the c_>_e around the pu_tey, , Pro@_edback around the opener sprockeL Figure 2. Be sure sprocket teeth engage t}he chain, Continue forward to the trolley thresd_ shaft, Figure 3. Use the se_:md master _nk to connect the chain to the flat end of the shaft. Check to make sure the chain is not twtsted, , Remove the screwdriver Master LJ_k Pr_r_; n The Oit_a P_sh pins of r_3_stet link bar through _b_e k_p a_ hole in #on_ end d t_liey, Push _p over pins_nd into risk;hoe Stag c_po_ spdng over_ep a_ into _yotchee unti_ _t_h pins are s_ure_y i_kedo To a_ach the sprocket cover: InseA the back t_ inthe opener sbt. Squeeze the cover slightly and inseA the front tab in the s/st on the mounting plate, 10 Spir_theinnernutandiockwasherdownthe threadedshaftaw...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: